Click here

AIRBAG SYSTEM, Diagnostic DTC:B1656

Click here
Click here Click here
DTC Code DTC Name
B1656 Seat Belt Buckle Switch (LH)
Click here

DESCRIPTION

The seat belt buckle switch LH circuit consists of the airbag ECU assembly and front seat inner belt assembly LH.

DTC B1656 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1656 Seat Belt Buckle Switch (LH)

One of the following conditions is met:


  • The airbag ECU assembly detects a line short, short to ground or B+, or an open in the seat belt buckle switch LH circuit.

  • A front seat inner belt assembly LH (seat belt buckle switch LH) malfunction

  • An airbag ECU assembly malfunction

  • Floor wire

  • Front seat inner belt assembly LH

  • Airbag ECU assembly

 Comes on Not applicable
Figure 2. for RHD: B004XJ6E52
Table 2.
*a Front Seat Inner Belt Assembly LH
*b Airbag ECU Assembly
Figure 1. for LHD: Table 1. *a Front Seat Inner Belt Assembly LH *b Airbag ECU Assembly
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

Click here

PROCEDURE


  1. Click here

    CHECK VEHICLE CONDITION


    1. Check vehicle condition.

      Result
      Proceed to
      for LHD
      for RHD

  2. Click here

    CHECK CONNECTION OF CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag ECU assembly and front seat inner belt assembly LH.

      Result
      Proceed to
      Connectors are properly connected
      Connectors are not properly connected

    • Connectors are properly connectedClick here
    • Connectors are not properly connected

      CONNECT CONNECTORS PROPERLY

  3. Click here

    CHECK CONNECTORS


    1. B004TEOC35
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire

      Disconnect the connectors from the airbag ECU assembly and front seat inner belt assembly LH.

    2. Check that the connectors (on the airbag ECU assembly side and front seat inner belt assembly LH side) are not damaged.

      Result
      Proceed to
      Connectors are not deformed or damaged
      Connectors are deformed or damaged

    • Connectors are not deformed or damagedClick here
    • Connectors are deformed or damaged

      REPLACE FLOOR WIRE

  4. Click here

    CHECK FLOOR WIRE


    1. B004USSC05
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Front Seat Inner Belt Assembly LH)
      *b

      Front view of wire harness connector

      (to Airbag ECU Assembly)

      Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L192-1 (LBE+) - Body ground Power switch on (IG) Below 1 V
      L192-3 (LBE-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 28 (LBE+) and 27 (LBE-) of connector B.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L192-1 (LBE+) - L192-3 (LBE-) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L192-1 (LBE+) - L192-3 (LBE-) Always 1 MΩ or higher
      L192-1 (LBE+) - Body ground Always 1 MΩ or higher
      L192-3 (LBE-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

  5. Click here

    CHECK DTC


    1. B004T4LC01
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly

      Connect the connectors to the airbag ECU assembly and front seat inner belt assembly LH.

    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B1656 is not output
      DTC B1656 is output
      Tip:

      Codes other than DTC B1656 may be output at this time, but they are not related to this check.


  6. Click here

    CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Replace the front seat inner belt assembly LH.

      Click here

      Tip:

      Perform the inspection using parts from a normal vehicle if possible.

      Result
      Proceed to
      NEXT

  7. Click here

    CHECK DTC


    1. B004T4LC01
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly

      Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    2. Turn the power switch on (IG), and wait for at least 60 seconds.

    3. Clear the DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B1656 is not output
      DTC B1656 is output
      Tip:

      Codes other than DTC B1656 may be output at this time, but they are not related to this check.


    • DTC B1656 is not output

      END (FRONT SEAT INNER BELT ASSEMBLY LH WAS DEFECTIVE)

    • DTC B1656 is output

      REPLACE AIRBAG ECU ASSEMBLYClick here

  8. Click here

    CHECK CONNECTION OF CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag ECU assembly and front seat inner belt assembly LH.

      Result
      Proceed to
      Connectors are properly connected
      Connectors are not properly connected

    • Connectors are properly connectedClick here
    • Connectors are not properly connected

      CONNECT CONNECTORS PROPERLY

  9. Click here

    CHECK CONNECTORS


    1. B004TEOC35
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire

      Disconnect the connectors from the airbag ECU assembly and front seat inner belt assembly LH.

    2. Check that the connectors (on the airbag ECU assembly side and front seat inner belt assembly LH side) are not damaged.

      Result
      Proceed to
      Connectors are not deformed or damaged
      Connectors are deformed or damaged

    • Connectors are not deformed or damagedClick here
    • Connectors are deformed or damaged

      REPLACE FLOOR WIRE

  10. Click here

    CHECK FLOOR WIRE


    1. B004W2VC01
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Front Seat Inner Belt Assembly LH)
      *b

      Front view of wire harness connector

      (to Airbag ECU Assembly)

      Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L19-2 (LBE+) - Body ground Power switch on (IG) Below 1 V
      L19-1 (LBE-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 28 (LBE+) and 27 (LBE-) of connector B.

      Note:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L19-2 (LBE+) - L19-1 (LBE-) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L19-2 (LBE+) - L19-1 (LBE-) Always 1 MΩ or higher
      L19-2 (LBE+) - Body ground Always 1 MΩ or higher
      L19-1 (LBE-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

  11. Click here

    CHECK DTC


    1. B004T4LC01
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly

      Connect the connectors to the airbag ECU assembly and front seat inner belt assembly LH.

    2. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B1656 is not output
      DTC B1656 is output
      Tip:

      Codes other than DTC B1656 may be output at this time, but they are not related to this check.


  12. Click here

    CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Replace the front seat inner belt assembly LH.

      Click here

      Tip:

      Perform the inspection using parts from a normal vehicle if possible.

      Result
      Proceed to
      NEXT

  13. Click here

    CHECK DTC


    1. B004T4LC01
      *1 Front Seat Inner Belt Assembly LH
      *2 Airbag ECU Assembly

      Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

    2. Turn the power switch on (IG), and wait for at least 60 seconds.

    3. Clear the DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Clear DTCs


    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      1. Body Electrical > SRS Airbag > Trouble Codes


      Result
      Proceed to
      DTC B1656 is not output
      DTC B1656 is output
      Tip:

      Codes other than DTC B1656 may be output at this time, but they are not related to this check.


    • DTC B1656 is not output

      END (FRONT SEAT INNER BELT ASSEMBLY LH WAS DEFECTIVE)

    • DTC B1656 is output

      REPLACE AIRBAG ECU ASSEMBLYClick here