Click here

REAR DOOR LOCK REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Replacement Part Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Removal and installation of auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type:Click here

for Mono Camera type:Click here
Lane control system (for Stereo camera type)
Parking support brake system*
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Initialize Rear Door Sunshade System Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here

  • Rear multiplex network door ECU LH

  • Rear multiplex network door ECU RH

  • Rear multiplex network door ECU LH or rear multiplex network door ECU RH is the connectors are disconnected

 Initialize rear door sunshade system The rear door sunshade system does not operate

Click here

  • Power window regulator motor assembly LH

  • Power window regulator motor assembly RH

  • Rear door window regulator assembly LH

  • Rear door window regulator assembly RH

  • Rear door glass sub-assembly LH

  • Rear door glass sub-assembly RH

  • Rear door glass run LH

  • Rear door glass run RH

  • Rear door No. 3 glass run LH

  • Rear door No. 3 glass run RH

 Initialize power window control system

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here
*: When performing learning using the GTS. Click hereClick here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When removing the rear door glass sub-assembly LH, move the rear door glass sub-assembly LH to the lowest position before disconnecting the auxiliary battery negative (-) terminal.

Click here

PROCEDURE


  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  4. Click here

    REMOVE REAR DOOR TRIM UPPER COVER LH

    Click here

  5. Click here

    REMOVE REAR DOOR ARMREST COVER LH

    Click here

  6. Click here

    REMOVE REAR DOOR NO. 2 ARMREST COVERLH

    Click here

  7. Click here

    REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  8. Click here

    REMOVE REAR DOOR TRIM COVER LH

    Click here

  9. Click here

    REMOVE REAR DOOR NO. 2 FRAME GARNISH LH

    Click here

  10. Click here

    REMOVE REAR DOOR FRAME GARNISH LH

    Click here

  11. Click here

    REMOVE CURTAIN RAIL SIDE COVER LH (w/ Rear Door Sunshade)

    Click here

  12. Click here

    REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)

    Click here

  13. Click here

    REMOVE REAR SIDE WINDOW COVER LH (w/ Rear Door Sunshade)

    Click here

  14. Click here

    REMOVE REAR DOOR GLASS INNER WEATHERSTRIP LH

    Click here

  15. Click here

    REMOVE REAR DOOR FRONT BELT SEAL LH

    Click here

  16. Click here

    REMOVE REAR DOOR REAR BELT SEAL LH

    Click here

  17. Click here

    REMOVE REAR SPEAKER ASSEMBLY

    Click here

  18. Click here

    REMOVE REAR MULTIPLEX NETWORK DOOR ECU LH

    Click here

  19. Click here

    REMOVE REAR DOOR SERVICE HOLE COVER LH

    Click here

  20. Click here

    REMOVE REAR DOOR FRONT BELT MOULDING END COVER LH

    Click here

  21. Click here

    REMOVE REAR DOOR REAR BELT MOULDING END COVER LH

    Click here

  22. Click here

    REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH

    Click here

  23. Click here

    REMOVE REAR DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

    Click here

  24. Click here

    REMOVE REAR DOOR WINDOW FRAME MOULDING LH (REAR PILLAR SIDE)

    Click here

  25. Click here

    REMOVE REAR DOOR OUTSIDE MOULDING INSERT LH

    Click here

  26. Click here

    REMOVE REAR DOOR BELT MOULDING LH

    Click here

  27. Click here

    REMOVE REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY LH

    Click here

  28. Click here

    REMOVE REAR DOOR GLASS RUN LH

    Click here

  29. Click here

    REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  30. Click here

    REMOVE REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH

    Click here

  31. Click here

    REMOVE REAR DOOR REAR WINDOW FRAME LH

    Click here

  32. Click here

    REMOVE REAR DOOR BELT MOULDING SUB-ASSEMBLY LH

    Click here

  33. Click here

    REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH

    Click here

  34. Click here

    REMOVE REAR DOOR NO. 3 GLASS RUN LH

    Click here

  35. Click here

    REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH

    Click here

  36. Click here

    REMOVE REAR DOOR LOCK ASSEMBLY LH


    1. B004Y4BC01
      B004SZX "TORX" screw
      B004UK4 Connector

      Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the 3 TORX screws.

    3. B004W2GC01
      *1 Release plate
      B004RMI Remove in this Direction

      Remove the 2 bolts.

    4. Remove the release plate of the rear door outside handle frame sub-assembly LH in the direction indicated by the arrow shown in the illustration to remove the rear door lock assembly LH.

      Note:

      Do not damage the vehicle body with the rear door lock assembly LH.

      Tip:

      Remove the rear door lock assembly LH while supporting it with one hand.

    5. When reusing rear door lock assembly LH:


      1. B004XCD

        Remove the door lock wire harness seal from the rear door lock assembly LH.

  37. Click here

    REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY LH


    1. B004VL5C01
      B004RMI Open in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver, detach the claw and open the rear door lock cover sub-assembly LH as shown in the illustration.

    2. B004SIA

      Detach the claw and remove the rear door lock cover sub-assembly LH.

  38. Click here

    REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B004Y4KC01
      B004RMI Remove in this Direction

      As shown in the illustration, detach the clamp and remove the rear door lock remote control cable assembly LH.

  39. Click here

    REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B004V8JC01
      B004RMI Remove in this Direction

      As shown in the illustration, detach the clamp and remove the rear door inside locking cable assembly LH.