NOISE FILTER

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the noise filter removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative auxiliary battery terminal	Memorize steering angle neutral point	LKA/LDA system (for Mono camera type)	for Stereo Camera type:Click here for Mono Camera type:Click here
		Lane control system (for Stereo camera type)
		Parking support brake system*
		Pre-collision system (for Mono camera type)
		Pre-collision system (for Stereo camera type)
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS. Click hereClick here

Click here

PROCEDURE

Click here
PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

Note:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here
Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
Click here
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
  
  Click here
- If the airbag deploys for any reason, it may cause a serious accident.
Note:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
Click here
REMOVE REAR SEAT ASSEMBLY
1. for Fixed Seat Type:
  
  Click here
2. for Power Seat:
  
  Click here
Click here
REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)

Note:
When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.
1. Remove the bolt.
2. Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
3. Remove in this Direction
  
  Detach the claw and pull out the cover as shown in the illustration.
4. Move in this Direction
  
  Using a screwdriver, detach the claws and remove the 2 terminal covers with wire harness from the condenser.
5. Move in this Direction
  
  Using a screwdriver, bend back and break off the claw as shown in the illustration.
6. Remove the terminal cover from the wire harness.
  Note:
  - Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
  - Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
  - Check for deformation of the terminal after the wire harness has been removed from the terminal cover.
Click here
REMOVE PACKAGE TRAY TRIM GARNISH LH

Click here
Click here
REMOVE PACKAGE TRAY TRIM SIDE COVER LH

Click here
Click here
REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

Click here
Click here
REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

Click here
Click here
REMOVE RADIO SETTING CONDENSER (for Window Defogger)

Note:
When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.
1. Remove the bolt.
2. Detach the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
3. Remove in this Direction
  
  Using a screwdriver, detach the claws and remove the terminal cover with wire harness from the condenser.
4. Using a screwdriver, bend back and break off the claw as shown in the illustration.
  Note:
  - Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
  - Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
  - Check for deformation of the terminal after the wire harness has been removed from the terminal cover.

NOISE FILTER REMOVAL