Click here

FRONT AXLE HUB(for 2WD) INSTALLATION

Click here
Click here Click here

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH side

  • The following procedure is for the LH side.

Click here

PROCEDURE


  1. Click here

    INSTALL DISC BRAKE AIR GUIDE PLATE


    1. Install disc brake air guide plate to the steering knuckle LH.

  2. Click here

    INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH


    1. Using a hexagon socket wrench 12 mm, install the front axle hub sub-assembly LH with the 4 bolts.

      80 N*m 816 kgf*cm 59 ft.*lbf
  3. Click here

    CONNECT STEERING KNUCKLE LH

    Click here

  4. Click here

    TEMPORARILY TIGHTEN LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B004WU8

      Insert the bolt from the back of the vehicle. Then temporarily tighten the lower No. 2 suspension arm assembly LH with the nut.

  5. Click here

    TEMPORARILY TIGHTEN FRONT PNEUMATIC CYLINDER ASSEMBLY WITH SHOCK ABSORBER LH (w/ Air Suspension)

    Click here

  6. Click here

    TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER ASSEMBLY LH (w/o Air Suspension)

    Click here

  7. Click here

    CONNECT FRONT STABILIZER LINK ASSEMBLY LH

    Click here

  8. Click here

    CONNECT FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

    Click here

  9. Click here

    TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM ASSEMBLY LH


    1. B004S1G

      Temporarily tighten the front lower suspension arm assembly LH to the steering knuckle assembly LH with the nut.

  10. Click here

    CONNECT TIE ROD ASSEMBLY LH

    Click here

  11. Click here

    INSTALL FRONT DISC BRAKE DUST COVER LH


    1. Install the front disc brake dust cover LH with the 3 bolts.

      8.0 N*m 82 kgf*cm 71 in.*lbf
  12. Click here

    INSPECT FRONT AXLE HUB BEARING LOOSENESS

    Click here

  13. Click here

    INSPECT FRONT AXLE HUB RUNOUT

    Click here

  14. Click here

    INSTALL FRONT DISC LH


  15. Click here

    CONNECT DISC BRAKE CYLINDER ASSEMBLY


    1. B004RX3

      Temporarily install the 5 hub nuts to the front axle hub LH to secure the front disc LH.

      Note:

      Do not apply excessive force to the flexible hose.

    2. Temporarily install the disc brake cylinder assembly LH with the bolt on the lower side of the disc brake cylinder assembly LH.

    3. Remove the SST.

    4. B004S2C

      Install the disc brake cylinder assembly LH with the 2 bolts.

      135 N*m 1377 kgf*cm 100 ft.*lbf
    5. B004S8R

      Install the front flexible hose bracket LH to the steering knuckle with the bolt.

      21 N*m 214 kgf*cm 15 ft.*lbf
    6. B004XUC

      Connect the flexible hose to the front flexible hose bracket LH with the bolt.

      20 N*m 204 kgf*cm 15 ft.*lbf

    7. for RH side:


      1. B004SNI

        Attach the guide to connect the pad wear indicator wire assembly.

  16. Click here

    CONNECT FRONT SKID CONTROL SENSOR WIRE


    1. B004YAA

      for LH Side:


      1. Install the sensor clamp with the bolt.

        10 N*m 102 kgf*cm 7 ft.*lbf
        Note:

        Do not twist the skid control sensor wire when installing it.

      2. Connect the skid control sensor wire connector.

    2. B004TP1

      for RH Side:


      1. Install the sensor clamp with the bolt.

        10 N*m 102 kgf*cm 7 ft.*lbf
        Note:

        Do not twist the skid control sensor wire when installing it.

      2. Connect the skid control sensor wire connector.

      3. Connect the pad wear indicator connector.

    3. B004VSD

      Install the sensor clamp with the nut.

      8.5 N*m 87 kgf*cm 75 in.*lbf
      Note:

      Do not twist the skid control sensor wire when installing it.

  17. Click here

    STABILIZE SUSPENSION

    Click here

  18. Click here

    FULLY TIGHTEN LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. Tighten the installation bolt of the lower No. 2 suspension arm assembly LH.

      130 N*m 1326 kgf*cm 96 ft.*lbf
  19. Click here

    FULLY TIGHTEN FRONT LOWER SUSPENSION ARM ASSEMBLY LH


    1. Tighten the installation nut of the steering knuckle assembly LH.

      145 N*m 1479 kgf*cm 107 ft.*lbf
      Note:

      Further tighten the nut up to 60° if the holes for the clip are not aligned.

    2. Install a new clip.

  20. Click here

    FULLY TIGHTEN FRONT SHOCK ABSORBER ASSEMBLY LH (w/o Air Suspension)


    1. Fully tighten the front shock absorber assembly bolt.

      110 N*m 1122 kgf*cm 81 ft.*lbf
      Note:

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  21. Click here

    FULLY TIGHTEN FRONT PNEUMATIC CYLINDER WITH SHOCK ABSORBER ASSEMBLY LH (w/ Air Suspension)


    1. Fully tighten the front pneumatic cylinder assembly with shock absorber LH bolt.

      110 N*m 1122 kgf*cm 81 ft.*lbf
      Note:

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  22. Click here

    INSTALL REAR LOWER ARM MOUNTING REINFORCEMENT SUB-ASSEMBLY LH

    Click here

  23. Click here

    INSTALL ENGINE SIDE COVER LH

    Click here

  24. Click here

    INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  25. Click here

    INSTALL FRONT WHEEL

    Click here

  26. Click here

    CONNECT BRAKE BOOSTER PUMP CONNECTOR

    Click here

  27. Click here

    CHECK FOR SPEED SENSOR SIGNAL

    Click here

  28. Click here

    INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  29. Click here

    INSPECT AND ADJUST VEHICLE HEIGHT (w/ Air Suspension)

    Click here

  30. Click here

    PERFORM INITIALIZATION

    Parking support brake system

    Click here
    Panoramic view monitor system

    Click here
    Parking assist monitor system

    Click here

    • w/o Air Suspension System:

    • Lighting system (EXT)

    Click here
  31. Click here

    ADJUST HEADLIGHT AIMING

    Click here