Click here

FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL REPLACEMENT

Click here
Click here Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front differential side gear shaft oil seal removal/installation are shown below.

Note:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Table 1. Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type:Click here

for Mono Camera type:Click here
Lane control system (for Stereo camera type)
Parking support brake system*1
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
ECM Vehicle Identification Number (VIN) registration DTC P063051 is output

Click here

  • Air leaks from intake system

  • Gas leak from exhaust system is repaired

 Inspection after repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here
Engine assembly Inspection after repair
Drive learning*2

  • Large shift shock

  • Deterioration of fuel efficiency

Click here
Parts between the steering wheel and tires have been removed/installed, replaced or adjusted Perform actuator angle neutral point calibration and initialization

  • Variable gear ratio steering system

  • Steering wheel off-center

  • DTCs are output

Click here
Suspension, tires, etc

  • Ultrasonic sensor detection angle

  • Ultrasonic sensor detection angle registration

 Parking support brake system

Click here

  • Parking assist ECU initialization

  • Adjust steering angle

  • Rear television camera view adjustment (for Rear camera detection system)

 Panoramic view monitor system

Click here
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system

Click here
*1: When performing learning using the GTS. Click hereClick here *2: After performing the confirmation driving pattern, if the shock during acceleration is large after calibrating the "A/T Code Reset", perform driving learning.
CAUTION:

  • B004YIH

    This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

  • If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

  • B004STG

    Be sure to wear insulating gloves when working on high voltage wiring or components.

  • If work is performed without wearing insulating gloves, there is a danger of electric shock.

  • B004VFAC01
    *a An Object Exceeding Weight Limit of Engine Lifter

    The engine assembly with hybrid vehicle transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with hybrid vehicle transmission assembly may fall off the engine lifter.

  • B004RDA

    To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

Note:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

Table 2. Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name See Procedure
Vehicle enrolled in telematics system (w/ Telematics Transceiver for G-BOOK) 6 minutes
Vehicle not enrolled in telematics system (w/ Telematics Transceiver for G-BOOK) 1 minute
Click here

PROCEDURE


  1. Click here

    PRECAUTION

    Click here

  2. Click here

    REMOVE ENGINE ASSEMBLY WITH HYBRID VEHICLE TRANSMISSION

    Click here

  3. Click here

    REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

    Click here

  4. Click here

    FIX DIFFERENTIAL CARRIER ASSEMBLY FRONT

    Click here

  5. Click here

    REMOVE FRONT DRIVE SHAFT OIL SEAL RH


    1. B004UA7N02

      Using SST, remove the front differential case oil seal LH.

      09308-00010
  6. Click here

    REMOVE FRONT DRIVE SHAFT OIL SEAL LH


    1. B004WXIN01

      Using SST, remove the front differential case oil seal RH.

      09308-00010
  7. Click here

    INSTALL FRONT DRIVE SHAFT OIL SEAL RH


    1. B004TZQC02
      *a

      24 to 25 mm (0.945 to 0.984 in.)

      (From the end of the front differential carrier)

      Using SST and a hammer, install a new front differential case oil seal RH.

      09608-32010
      09950-70010 09951-07100
      Standard depth
      24.0 to 25.0 mm (0.9450 to 0.984 in.)
      (From the end of the front differential carrier)
      Note:

      • Tap the front differential case oil seal uniformly so that the front differential case oil seal is straight.

      • Do not excessively tap the front differential case oil seal.

      • Make sure the difference between the maximum and minimum measured values is less than 0.47 mm (0.0185 in.), as a greater difference may lead to oil leaks.

      • Using a vernier caliper, measure the depth of the front drive shaft oil seal RH.

  8. Click here

    INSTALL FRONT DRIVE SHAFT OIL SEAL LH


    1. B004YJ0C01
      *a -0.5 to 0.5 mm (-0.0197 to 0.0196 in.)

      Using SST and a hammer, install a new front differential case oil seal RH.

      09608-32010
      09950-70010 09951-07100
      Standard depth
      -0.5 to 0.5 mm (-0.0197 to 0.0196 in.)
      Note:

      • Tap the front differential case oil seal uniformly so that the front differential case oil seal is straight.

      • Do not excessively tap the front differential case oil seal.

      • Make sure the difference between the maximum and minimum measured values is less than 0.47 mm (0.0185 in.), as a greater difference may lead to oil leaks.

      • Using a vernier caliper, measure the depth of the front drive shaft oil seal RH.

  9. Click here

    REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

    Click here

  10. Click here

    INSTALL DIFFERENTIAL CARRIER ASSEMBLY FRONT

    Click here

  11. Click here

    INSTALL ENGINE ASSEMBLY WITH HYBRID VEHICLE TRANSMISSION

    Click here