Click here

OIL PUMP REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

CAUTION:

Do not turn the power switch on (READY) until the oil pump assembly with motor installation is completed.

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during oil pump assembly with motor removal/installation are shown below.

Note:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Table 1. Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point LKA/LDA system (for Mono camera type)

for Stereo Camera type:Click here

for Mono Camera type:Click here
Lane control system (for Stereo camera type)
Parking support brake system*1
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Adaptive high beam system

  • Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here
Parking assist monitor system

Click here
Panoramic view monitor system

Click here
Initialize rear door sunshade system Rear door sunshade system

Click here
Initialize power trunk lid system Power trunk lid system

Click here
*1: When performing learning using the GTS. Click hereClick here
Note:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.

Table 2. Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal
System Name See Procedure
Vehicle enrolled in telematics system (w/ Telematics Transceiver for G-BOOK) 6 minutes
Vehicle not enrolled in telematics system (w/ Telematics Transceiver for G-BOOK) 1 minute
Click here

PROCEDURE


  1. Click here

    DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  2. Click here

    REMOVE V-BANK COVER SUB-ASSEMBLY

    Click here

  3. Click here

    REMOVE RADIATOR COVER PLATE

    Click here

  4. Click here

    REMOVE LOWER RADIATOR AIR DEFLECTOR

    Click here

  5. Click here

    REMOVE RADIATOR SUPPORT TO CROSS MEMBER BRACE SUB-ASSEMBLY RH

    Click here

  6. Click here

    REMOVE NO. 1 AIR CLEANER INLET

    Click here

  7. Click here

    REMOVE AIR CLEANER ASSEMBLY

    Click here

  8. Click here

    REMOVE TRANSMISSION UNDER COVER

    Click here

  9. Click here

    REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  10. Click here

    DRAIN TRANSMISSION FLUID

    Click here

  11. Click here

    REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY


    1. B004RQ0

      Remove the 2 bolts and 2 nuts, disconnect the No. 1 exhaust pipe support bracket sub-assembly from the exhaust manifold assembly LH and exhaust manifold assembly RH.

    2. Remove the 2 bolts and No. 1 exhaust pipe support bracket sub-assembly.

  12. Click here

    REMOVE TRANSMISSION OIL PUMP INSULATOR


    1. B004RJ9

      Remove the 3 bolts and transmission oil pump insulator.

  13. Click here

    REMOVE TRANSMISSION OIL PUMP INSULATOR BRACKET


    1. B004XL7

      Remove the bolt and transmission oil pump insulator bracket.

  14. Click here

    DISCONNECT CONNECTOR

    Click here

  15. Click here

    DISCONNECT WIRE HARNESS


    1. B004UW9

      Disconnect the oil pump thermistor connector.

    2. Disconnect the 9 wire harness clamps.

  16. Click here

    REMOVE OIL WITH MOTOR PUMP ASSEMBLY


    1. B004UJT

      Disconnect the transmission breather hose from the oil with motor pump assembly.

    2. Remove the 4 bolts, gasket and oil with motor pump assembly from the hybrid vehicle transmission assembly.