ROOF HEADLINING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the roof headlining assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here


  • Front Seat Assembly RH (Only for removal and installation)

  • Front Seat Assembly LH (Only for removal and installation)

 Initialize position control ECU Front Power Seat Control System

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B004CGW

Click here

Tech Tips


  • Use the same procedure as for the LHD and RHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. REMOVE REAR SEAT ASSEMBLY

    Click here

  4. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

    Click here

  5. REMOVE NO. 1 CONSOLE BOX SUPPORT

    Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  7. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE FRONT DOOR OPENING TRIM COVER LH

    Click here

  9. REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER LH

    Click here

  11. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER RH

    Click here

  12. REMOVE FRONT PILLAR GARNISH LH


    1. B004B23C01
      B004CG0 Protective Tape

      Apply protective tape at the position shown in the illustration.

    2. B004AEOC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction of the arrow shown in the illustration to detach the front pillar garnish clip and lift up the front pillar garnish LH.

    3. B004AXIC01
      *a Release Lever
      B004C4F Push

      Push in the release lever with your finger and remove the front pillar garnish clip from the vehicle.

      Note

      If there is extreme damage to the front pillar garnish clip, replace it with a new one.

    4. When the front pillar garnish clip cannot be detached by pressing the knobs with the fingers:


      1. B004AV7C01
        B004B1M Direction (A)
        B004C4F Push

        Lift up the front pillar garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

      2. B004BHSC01
        B004B1M Direction (B)
        B004C4F Release Lever
        B004ANI Push

        Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the front pillar garnish clip with your fingers in the direction (B) to detach the front pillar garnish clip.

        Note

        If there is extreme damage to the front pillar garnish clip, replace it with a new one.

    5. B0049U4C01
      B004B1M Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the clip.

    6. B004CBWC01
      B004B1M Remove in this Direction

      Pull the front pillar garnish LH in the direction of the arrow shown in the illustration to detach the guides and remove the front pillar garnish LH.

    7. B004ALVC01
      *a Protective Cover
      B004CG0 Adhesive Tape

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure both ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.

  13. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE OUTER LAP BELT ANCHOR COVER

    Tech Tips

    Use the same procedure for the opposite side.

    Click here

  15. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH(FLOOR ANCHOR)

    Click here

  16. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH(FLOOR ANCHOR)

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE QUARTER INSIDE TRIM BOARD LH


    1. B004BQOC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws and remove the quarter inside trim board LH.

  18. REMOVE QUARTER INSIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  20. REMOVE REAR SEAT INNER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the rear No. 1 seat inner belt assembly LH.

  21. REMOVE QUARTER TRIM PANEL ASSEMBLY LH


    1. B0049VE

      Detach the clamp.

    2. B004AT9

      Remove the 2 clips.

    3. B004CR6C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and detach the hook.

    4. Pull in the direction of the arrow shown in the illustration to detach the claws and clip.

    5. B004BJDC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws and clip.

    6. B004AGAC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction
      B004C4F Order of Removal

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws in order.

    7. B004BH2C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clips.

    8. B004B6UC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and detach the clip to remove the quarter trim panel assembly LH.

    9. B004AYH

      Disconnect the connector.

  22. REMOVE QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH


    1. B004BLX

      Remove the 2 clips.

    2. B0049TLC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the hooks.

    3. B004C0TC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claw and clip.

    4. B004AE8C01
      B004B1M Remove in this Direction

      Detach the claws.

    5. Detach the guide in the direction of the arrow shown in the illustration and remove the seat belt guide LH.

    6. Pull out the seat belt guide LH and front seat outer belt assembly LH (floor anchor) from the center pillar garnish assembly LH and remove the center pillar garnish assembly LH.

  24. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. REMOVE INNER ROOF SIDE GARNISH LH


    1. B004B2UC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.

    2. B004ANCC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip.

    3. B004BBEC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction
      B004C4F Order of Removal

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow and detach the claw and clips in order to remove the inner roof side garnish LH.

  26. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH


    1. B004AGOC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the clip and roof side trim garnish clip.

    2. B004C91C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and detach the clip.

    3. B004BWXC01
      *a Release Lever
      B004C4F Push

      Push in the release lever with your finger, detach the roof side trim garnish clip from the vehicle and remove the roof side rail garnish assembly LH.

      Note

      If there is extreme damage to the roof side trim garnish clip, replace it with a new one.

    4. When the roof side trim garnish clip cannot be detached by pressing the knobs with the fingers:


      1. B004AV7C02
        B004B1M Direction (A)
        B004C4F Push

        Lift up the roof side trim garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

      2. B004BWBC03
        B004B1M Direction (B)
        B004C4F Release Lever
        B004ANI Push

        Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the roof side trim garnish clip with your fingers in the direction (B) to detach the roof side trim garnish clip.

        Note

        If there is extreme damage to the roof side trim garnish clip, replace it with a new one.

  28. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH


    1. B004A03C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the inner upper roof side garnish clips.

    2. B004CSGC02
      *a Release Lever
      B004C4F Push

      Push in the release lever with your finger and remove the inner upper roof side garnish clips from the vehicle.

      Note

      If there is extreme damage to the inner upper roof side garnish clip, replace it with a new one.

    3. When the inner upper roof side garnish clip cannot be detached by pressing the knobs with the fingers:


      1. B004AV7C03
        B004B1M Direction (A)
        B004C4F Push

        Lift up the inner upper roof side garnish clip in the direction (A) while pressing the portion indicated by the arrow in the illustration with your fingers.

      2. B004BWBC04
        B004B1M Direction (B)
        B004C4F Release Lever
        B004ANI Push

        Push in the portion indicated by the arrow in the illustration with the screwdriver end while pulling the inner upper roof side garnish clip with your fingers in the direction (B) to detach the inner upper roof side garnish clip.

        Note

        If there is extreme damage to the inner upper roof side garnish clip, replace it with a new one.

    4. B004BG4C01
      B004B1M Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the guides to remove the inner roof side garnish assembly LH.

    5. B004CF3C01
      *a Protective Cover
      B004CG0 Adhesive Tape

      Protect curtain shield airbag assembly:


      1. Cover the airbag with a cloth or piece of nylon and secure both ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag assembly with a protective cover as soon as the inner roof side garnish assembly LH is removed.

  30. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  31. REMOVE VISOR BRACKET COVER LH


    1. B004C2P

      Detach the claws and remove the visor bracket cover LH.

  32. REMOVE VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  33. REMOVE VISOR ASSEMBLY LH


    1. B004BR9

      Remove the 2 screws.

    2. B004C45C01
      B004B1M Remove in this Direction (1)
      B004CNL Remove in this Direction (2)

      Pull in the direction of the arrow shown in the illustration (1) to detach the visor assembly LH from the visor holder LH.

    3. Pull in the direction of the arrow shown in the illustration (2) and remove the visor assembly LH.

      Note

      Do not twist or remove the visor assembly in any direction other than downwards as the connector may become damaged.

  34. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  35. REMOVE MAP LIGHT SUB-ASSEMBLY

    Click here

  36. REMOVE RAIN SENSOR COVER

    Click here

  37. REMOVE VISOR HOLDER LH


    1. B004C3BC02
      *a 90°
      B004B1M Remove in this Direction (1)
      B004CNL Remove in this Direction (2)

      Turn the visor holder LH end approximately 90° in direction (1) indicated by the arrow shown in the illustration, and pull it out in direction (2) indicated by the arrow.

    2. Detach the claws and remove the visor holder LH.

  38. REMOVE VISOR HOLDER RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE ROOF HEADLINING ASSEMBLY


    1. B004C8D

      Disconnect the 2 connectors.

    2. Front pillar LH part:


      1. Remove the protective cover installed to the front pillar LH.

      2. B004BFP

        Disconnect the 2 connectors.

      3. Using a clip remover, detach the clamps and disconnect the No. 1 roof wire.

      4. Install the protective cover to the front pillar LH.

    3. B004CTB

      Remove the screw from the coat hook.

      Tech Tips

      Use the same procedure for the opposite side.

    4. B004C71C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and detach the claws.

      Tech Tips

      Use the same procedure for the other side.

    5. B004ARYC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      for Carbon Roof:

      Place your hand at the position shown in the illustration and detach the fasteners.

    6. B004C9MC01
      B004B1M Remove in this Direction

      for Glass Roof:

      Detach the fastener.

    7. B0049XVC02
      B004B1M Remove in this Direction

      Slide the roof headlining assembly toward the rear of the vehicle and detach the clips.

      Tech Tips

      The 3 clips remain on the vehicle side.

    8. B004BD9

      Remove the roof headlining:

    9. Move the roof headlining assembly as shown in the illustration and remove it from the passenger door without making contact with the body interior.

      B004CJDC01
      B004B1M Remove in this Direction - -

      Note


      • Check that the corners of the roof headlining assembly are free of bending, twisting and other deformation and that none of the mounted parts are falling off.

      • Do not damage the roof headlining assembly and body interior.

      • 2 or more people are required when carrying the roof headlining assembly out of the vehicle, as it may become deformed.

    10. B004BRRC01
      B004B1M Remove in this Direction

      Turn in the direction of the arrow shown in the illustration and remove the 3 clips from the vehicle.

    11. B004BIW

      Remove the grommet from the vehicle.

      Tech Tips

      Use the same procedure for the RH side.

  40. REMOVE ROOF SIDE RAIL GARNISH


    1. B004CTLC01
      B004B1M Remove in this Direction

      Detach the clamps and remove the roof side rail garnish.

      Tech Tips

      Use the same procedure for the opposite side.