INSTRUMENT PANEL SAFETY PAD REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the instrument panel safety pad sub-assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point LKA/LDA system

Click here

Pre-collision system
Parking assist monitor system

Click here

Steering sensor zero point calibration Variable gear ratio steering system

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B004CGW

Click here

Tech Tips


  • Use the same procedure as for the LHD and RHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND NUT

    Tech Tips

    All bolts and screws relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.

    B004BFZE03
  2. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  4. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS

    Click here

  5. REMOVE NO. 2 DECK BOARD

    Click here

  6. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

    CAUTION:

    B004A52

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Click here

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

    Click here

  7. REMOVE CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL


    1. B004BKZC01
      B0049X5 Place hands here
      B004B1M Remove in this Direction

      Place both hands at the position shown in the illustration and pull towards the rear of the vehicle to detach the clips, claw and guides.

    2. B004CDHC01
      B004B1M Remove in this Direction

      Lift up the center upper instrument cluster finish panel as shown in the illustration to remove it.

  8. REMOVE METER HOOD SUB-ASSEMBLY


    1. B004A6E

      Disconnect the 2 connectors.

    2. B004AEKN01

      Remove the screw <F> or <H> and 2 screws.

    3. B004COJ

      Remove the 2 screws.

    4. B004BSPC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Pull the part in the removal direction shown in the illustration to detach the clips and guides and remove the meter hood sub-assembly.

  9. REMOVE COMBINATION METER ASSEMBLY

    Click here

  10. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B004C5BC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and open the front door scuff plate LH towards the center of the vehicle. Then, lift it up in the direction of the arrow to detach the claws and guide.

    2. B004CK6C01
      B0049X5 Place hands here
      B004B1M Remove in this Direction
      B004C4F Order of Removal

      Place both hands in the gap in the vehicle and while pulling in the direction of the arrow shown in the illustration to detach the clips, claws and guide and remove the front door scuff plate LH.

  11. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT DOOR OPENING TRIM COVER LH


    1. B004C9RC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction of the arrow to detach the claws and guide and remove the front door opening trim cover LH.

  13. REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER LH


    1. B004CDSC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    2. B004CTRC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction of the arrow to detach the clip and claw and remove the front door No. 2 opening trim cover LH.

  15. REMOVE FRONT DOOR NO. 2 OPENING TRIM COVER RH


    1. B004AC4C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    2. B004BOZC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction of the arrow to detach the clip and claw and remove the front door No. 2 opening trim cover RH.

  16. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. for LHD:


      1. B004B8A

        Remove the 2 screws.

      2. B004C7LC01
        B004B1M Remove in this Direction

        Detach the claws and lower the No. 1 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.

      3. B004AM7C01
        B004B1M Remove in this Direction

        Detach the claw of the arrow shown in the illustration.

      4. B004CN7

        Disconnect the connector.

      5. B004CKHC01
        B004B1M Remove in this Direction

        Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 1 instrument panel under cover sub-assembly.

    2. for RHD:


      1. B004AE1

        Remove the 2 screws.

      2. B004BXZC02
        B004B1M Remove in this Direction

        Detach the claws and lower the No. 1 instrument panel under cover sub-assembly in the direction of the arrow shown in the illustration.

      3. B004BO3

        Disconnect the connector.

      4. B004AQWC03
        B004B1M Remove in this Direction

        Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 1 instrument panel under cover sub-assembly.

  17. REMOVE NO. 1 GLOVE COMPARTMENT PANEL


    1. B004CE1C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction
      B004C4F Order of Removal

      Place your hand at the position shown in the illustration and pull the No. 1 glove compartment panel towards the rear of the vehicle to detach the clips and remove the No. 1 glove compartment panel.

  18. REMOVE CONSOLE BOX ASSEMBLY (for LHD)

    Click here

  19. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for RHD)

    Click here

  20. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    1. B004C8MC01
      B004CG0 Protective Tape

      Apply protective tape at the position shown in the illustration.

    2. B004CBN

      Insert moulding remover A at the position shown in the illustration and detach the claw.

    3. B004AWYC02
      B0049X5 Place hand here
      B004B1M Remove in this Direction
      B004C4F Order of Removal

      Place your hand in the gap and pull diagonally to the upper rear of the vehicle to detach the claws and guides and remove the No. 2 instrument panel garnish sub-assembly.

  21. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B004BK2

      Detach the claw and guides and remove the hood lock control lever sub-assembly from the No. 1 instrument panel safety pad sub-assembly.

  22. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. B004BU0N01

      Remove the 3 bolts <E>.

    2. B004BL4C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws and guide.

    3. B004BF4C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Pull in the direction indicated by the arrow shown in the illustration to detach the clips.

    4. B004AER

      Detach the clamp and disconnect the 2 connectors.

    5. B004CCM

      Detach the clamps and disconnect the 2 connectors and remove the No. 1 instrument panel safety pad sub-assembly.

  23. REMOVE INSTRUMENT PANEL REGISTER BEZEL


    1. B004AX1C01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    2. B004B9XC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the claws and remove the instrument panel register bezel.

  24. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY

    Click here

  25. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET

    Click here

  26. REMOVE TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ Telematics Transceiver)

    Click here

  27. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B004AGKC01
      B004CG0 Protective Tape

      Apply protective tape at the position shown in the illustration.

    2. B004A8HC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the claws.

    3. B004A63

      Pull the No. 2 instrument panel register assembly and disconnect the connector and remove the No. 2 instrument panel register assembly.

  28. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B004AA8C01
      B004B1M Remove in this Direction

      Detach the claws and lower the No. 2 instrument panel under over sub-assembly in the direction of the arrow shown in the illustration.

    2. B004AAV

      Disconnect the connector.

    3. B0049UOC01
      B004B1M Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 2 instrument panel under cover sub-assembly.

  29. REMOVE NO. 2 GLOVE COMPARTMENT PANEL


    1. B004CLDC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull the No. 2 glove compartment panel towards the outside of the vehicle to detach the claws and remove the No. 2 glove compartment panel.

    2. w/ Airbag Cut Off Switch:

      Disconnect the connector.

  30. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  31. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. B004CQ2C01
      B004C4F Bolt <E>
      B004ANI Screw <G>

      Detach the clamp.

    2. Remove the 2 bolts <E> and 2 screws <G>.

    3. B004AGGC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Place your hand at the position shown in the illustration and pull in the direction indicated by the arrow to detach the claws.

    4. B004CV4C01
      *a Clamp
      *b Hook

      Detach the clamps and hook and remove the glove compartment box assembly.

    5. Disconnect the 3 connectors.

  32. REMOVE MULTI-DISPLAY

    Click here

  33. REMOVE FRONT PILLAR GARNISH LH

    Click here

  34. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  35. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. for LHD:


      1. B004AL8

        Disconnect the 2 connectors.

      2. B004ANE

        Detach the claw and remove the connector holder.

    2. B0049ZYC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Lift up the part in the removal direction shown in the illustration to detach the claws.

    3. B004CQAC01
      B004B1M Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 1 instrument panel speaker panel sub-assembly.

  36. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. for RHD:


      1. B004AL8

        Disconnect the 2 connectors.

      2. B004ANE

        Detach the claw and remove the connector holder.

    2. B004BEKC01
      B0049X5 Place hand here
      B004B1M Remove in this Direction

      Lift up the part in the removal direction shown in the illustration to detach the claws.

    3. B004COWC01
      B004B1M Remove in this Direction

      Pull in the direction of the arrow shown in the illustration to detach the guides and remove the No. 2 instrument panel speaker panel sub-assembly.

  37. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  38. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  39. REMOVE STEERING WHEEL SWITCH HOUSING

    Click here

  40. REMOVE NO. 2 AIR DUCT


    1. B004A6FC02
      B004B1M Remove in this Direction

      Remove the 2 bolts and No. 2 air duct in the direction of the arrow shown in the illustration.

  41. REMOVE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)

    Click here

  42. REMOVE HEATER TO REGISTER CENTER SUB DUCT


    1. B004BP4N01

      Remove the 2 screws <F> or <H> and heater to register center sub duct.

  43. REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY


    1. for LHD:


      1. B004A3AC03
        *A w/ Clearance Sonar System
        B004C4F Bolt <A>
        B004ANI Nut <B>

        Detach the clamps.

      2. Remove the bolt <A>, nut <B> and No. 3 instrument panel to cowl brace sub-assembly.

    2. for RHD:


      1. B004BXJC04
        *A w/ Clearance Sonar System
        *1 DLC3
        B004C4F Bolt <A>
        B004ANI Nut <B>

        Detach the clamps.

      2. Detach the claws and remove the DLC3.

      3. Remove the bolt <A>, nut <B> and No. 3 instrument panel to cowl brace sub-assembly.

  44. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Disconnect airbag connector:


      1. Push down the housing lock and slide the CPA to release the lock.

        Note

        Do not pull while holding the wire harness.

        B004AW3C02
        *a Housing Lock *b CPA
        *c Disconnect the connector lock - -
      2. With the housing lock pushed down again, slide the CPA to disconnect the airbag connector.

      3. After disconnecting the airbag connector, check that the CPA is positioned further back than the housing.

        B004AN3C05
        *a CORRECT *b INCORRECT
        *c CPA *d Housing
    2. B004BLLN01

      Remove the 2 bolts <I>.

    3. for LHD:


      1. B004BN0

        Detach the clamp and disconnect the connector.

      2. B0049YJ

        Detach the clamps.

      3. B004AZJ

        Disconnect the connector.

    4. for RHD:


      1. B004BIT

        Detach the clamp and disconnect the connector.

      2. B004C5W

        Detach the clamps.

      3. B004CLJ

        Disconnect the connector.

    5. B004BMN

      Disconnect the 2 connectors.

    6. for LHD:


      1. Detach the claws and remove the cooler thermistor (recirculated air temperature) from the instrument panel safety pad sub-assembly.

        B004CCWC01
        *1 Cooler Thermistor (Recirculated Air Temperature) - -
        B004C4F Bolt <E> B004ANI Nut <C> or <D>
      2. Detach the clamp.

      3. Remove the 8 bolts <E>, and nut <C> or <D>.

    7. for RHD:


      1. Detach the claws and remove the cooler thermistor (recirculated air temperature) from the instrument panel safety pad sub-assembly.

        B004B81C04
        *1 Cooler Thermistor (Recirculated Air Temperature) - -
        B004C4F Bolt <E> B004ANI Nut <C> or <D>
      2. Remove the 8 bolts <E>, and nut <C> or <D>.

    8. Pull as shown in the illustration to detach the guides.

      B004C3UC01
      B004B1M Remove in this Direction - -
    9. Lift up the instrument panel safety pad sub-assembly as shown in the illustration to remove it.

      B004CHNC01
      B004B1M Remove in this Direction - -