BLACK OUT TAPE(for Rear Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

    Click here

  5. REMOVE REAR DOOR ARMREST COVER

    Click here

  6. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

    Click here

  9. REMOVE REAR DOOR NO. 2 TRIM BRACKET

    Click here

  10. REMOVE REAR DOOR SERVICE HOLE COVER

    Click here

  11. REMOVE REAR DOOR GLASS RUN

    Click here

  12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

    Click here

  13. DISCONNECT REAR DOOR WEATHERSTRIP

    Click here

  14. REMOVE REAR DOOR REAR GUIDE SEAL

    Click here

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  16. DISCONNECT REAR DOOR WEATHERSTRIP

    Click here

  17. REMOVE REAR DOOR FRONT BELT SEAL

    Click here

  18. REMOVE REAR DOOR FRAME GARNISH

    Click here

  19. REMOVE REAR DOOR LOWER OUTSIDE STRIPE

    Tech Tips

    When removing the rear door lower outside stripe, heat the vehicle body and rear door lower outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Rear Door Lower Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B005MXIC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the rear door lower outside stripe and vehicle body.

    2. B005M47

      Pull back on one of the ends of the rear door lower outside stripe to remove it.

      Tech Tips

      When pulling on the rear door lower outside stripe, pull it parallel to the body.

  20. REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)

    Click here

  21. REMOVE REAR DOOR OUTSIDE STRIPE

    Tech Tips

    When removing the rear door outside stripe, heat the vehicle body and rear door outside stripe using a heat light.

    Heating Temperature
    Item Temperature
    Rear Door Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B005MXIC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the rear door outside stripe and vehicle body.

    2. B005MP5

      Pull back on one of the ends of the rear door outside stripe to remove it.

      Tech Tips

      When pulling on the rear door outside stripe, pull it parallel to the body.

  22. REMOVE REAR INNER BLACK OUT TAPE

    Tech Tips

    When removing the rear inner black out tape, heat the vehicle body and rear inner black out tape using a heat light.

    Heating Temperature
    Item Temperature
    Rear Inner Black Out Tape and Vehicle Body 40 to 60°C (104 to 140°F)

    CAUTION:


    • Do not touch the heat light and heated parts, touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B005MXIC23
    *a Heated Part
    *b Heat Light

    Note

    Do not heat the vehicle body excessively.


    1. Using a heat light, heat the rear inner black out tape and vehicle body.

    2. B005OCP

      Pull back on one of the ends of the rear inner black out tape to remove it.

      Tech Tips

      When pulling on the rear inner black out tape, pull it parallel to the body.