REAR NO. 1 SEAT OUTER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear No. 1 seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-Crash Safety System

Lighting System (EXT)


  • Cornering lights
Adaptive High Beam System
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic View Monitor System

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B005NS4

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If an SRS part is accidentally deployed, it may cause a serious injury.

    B005NWT

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  4. REMOVE REAR DOOR SCUFF PLATE

    Click here

  5. REMOVE REAR DOOR INSIDE SCUFF PLATE

    Click here

  6. REMOVE REAR SEAT OUTER TRACK BRACKET COVER LH (for LH Side)

    Click here

  7. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH (for RH Side)

    Click here

  8. REMOVE FRONT DECK SIDE TRIM COVER

    Click here

  9. REMOVE REAR SEAT SIDE GARNISH

    Click here

  10. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

    Click here

  11. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

    Click here

  12. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)

    Click here

  13. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

    Click here

  14. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  15. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side)

    Click here

  16. REMOVE NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (for LH Side)

    Click here

  17. REMOVE COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (for LH Side)

    Click here

  18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

    Click here

  19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

    Click here

  20. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY


    1. B005P6C

      Remove the bolt to disconnect the floor anchor of the rear No. 2 seat outer belt assembly.

    2. B005L5E

      Disengage the 4 claws and 2 guides.

  21. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY

    Click here

  22. REMOVE REAR NO. 2 SIDE AIR DUCT (for RH Side)

    Click here

  23. REMOVE REAR NO. 7 AIR DUCT (for RH Side)

    Click here

  24. REMOVE REAR NO. 6 AIR DUCT (for RH Side)

    Click here

  25. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    1. B005Q2M

      Remove the bolt to disconnect the floor anchor of the rear No. 1 seat outer belt assembly.

  26. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    1. B005NX1

      Remove the 4 bolts.

    2. Disengage the 2 guides.

    3. B005ON5C02
      *a Locking Button
      *b Protective Tape
      *c Release

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    4. B005N5H

      Remove the nut.

    5. Disengage the 2 guides to remove the rear No. 1 seat outer belt assembly LH from the outer belt anchor bracket sub-assembly LH.

  27. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH


    1. B005L3GC02
      *a Locking Button
      *b Protective Tape
      *c Release

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B005PTK

      Remove the 4 bolts.

    3. Disengage the 2 guides.

    4. B005MO7

      Remove the nut.

    5. Disengage the 2 guides to remove the rear No. 1 seat outer belt assembly RH from the outer belt anchor bracket sub-assembly RH.