REAR SEAT ASSEMBLY(for 60/40 Split Seat Type RH Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-Crash Safety System

Lighting System (EXT)


  • Cornering lights
Adaptive High Beam System
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Memorize steering angle neutral point Panoramic View Monitor System

Click here

Memorize steering angle neutral point Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Fold seat control ECU (for RH side)

  • Rear seatback frame sub-assembly RH

 Initial position memorization Rear power seat function

Click here

*1: When performing learning using the GTS.

Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • B005PP8

      Be sure to read Precaution thoroughly before servicing.

      Click here

    • Wear protective gloves. Sharp areas on the seat frame may injure your hands.

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE TONNEAU COVER ASSEMBLY

    Click here

  3. REMOVE DECK BOARD ASSEMBLY

    Click here

  4. REMOVE REAR SEAT HEADREST ASSEMBLY


    1. Remove the rear seat headrest assembly.

  5. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY


    1. Remove the rear seat center headrest assembly.

  6. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH


    1. B005NU7C02
      B005M6U Place Hand Here
      B005OOA Remove in this Direction

      Disengage the 2 claws and 2 guides to remove the rear seat outer track bracket cover RH as shown in the illustration.

  7. REMOVE REAR SEAT INNER TRACK BRACKET COVER RH

    Tech Tips

    Use the same procedure as for the rear seat outer track bracket cover RH.

  8. DISCONNECT REAR SEAT ASSEMBLY RH


    1. B005LOH

      Using a clip remover, remove the 4 clips.

    2. Remove the bolt.

    3. B005MV6C01
      B005M97 Fastener

      Disengage the fastener to disconnect the rear seat assembly RH.

  9. DISCONNECT REAR SEAT RECLINING CONTROL CABLE (for Manual Seat)


    1. Lift the seat track adjusting handle and move the rear seat assembly RH to the foremost position.

    2. Pull out the lock lever to release the adjuster spring as shown in the illustration.

      B005LXXC01
      *a Adjuster Spring *b Lock Lever
    3. B005NELC01
      *a Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    4. B005LP9C01
      B005OOA Remove in this Direction

      Remove the joint case cover from the joint case as shown in the illustration.

    5. B005NEV

      Lift and hold the No. 1 reclining adjuster release handle RH at the uppermost position as shown in the illustration.

    6. B005LPSC01
      *a Protective Tape
      B005OOA Remove in this Direction

      Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    7. Using a screwdriver with its tip wrapped with protective tape, disconnect the reclining remote control lever sub-assembly RH as shown in the illustration.

      B005NT8C01
      *a Protective Tape - -

  10. REMOVE REAR SEAT ASSEMBLY RH


    1. for Power Seat:


      1. Lift the seat track adjusting handle and move the rear seat assembly RH to the foremost position.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    3. Disconnect the rear seat airbag assembly connector under the rear seat assembly RH.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. B005MIEC14
        *a White Housing Lock
        *b Yellow CPA
        B005NIZ Slide

        Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    4. Disconnect the connector.

    5. B005MHXC03
      *a Rubber Band

      Remove the rear center seat inner belt assembly from the rubber band of the rear seat cushion assembly RH as shown in the illustration.

    6. Lift the seat track adjusting handle and move the rear seat assembly RH to the foremost position.

    7. B005MM8

      Remove the 3 bolts.

    8. B005OZ0

      Remove the 2 bolts and rear seat assembly RH.

      Note

      Be careful not to damage the vehicle body.