CURTAIN SHIELD AIRBAG ASSEMBLY(w/o Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B005PP8

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B005NWT

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  4. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

    CAUTION:

    When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.

    B005N4DC02
    B005M97 Deployment Side

    Note

    When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B005NWT
    3. B005LXTC01
      *a Airbag Connector
      *b Airbag Connector Lock
      *c Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock and disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    4. Using needle nose pliers, remove the 5 pins from the 5 clips (A).

      Note

      Do not damage the pins.

      B005LUWC01
      *1 Pin *2 Spacer
      *a Clip (A) *b Clip (B)
      *c Spacer Location - -

    5. Using 2 screwdrivers, disengage the 2 claws of each clip (A) and separate the 5 clips (A) from the vehicle body as shown in the illustration.

      Tech Tips

      Separate the 5 clips (A) and curtain shield airbag assembly from the vehicle body as a unit.

    6. Disengage the 6 clips (B).

    7. While holding the curtain shield airbag assembly, remove the 6 bolts, disengage the 2 hooks and remove the curtain shield airbag assembly.

    8. Remove the 5 clips (A) and 2 spacers from the curtain shield airbag assembly.