FRONT PASSENGER AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the instrument panel passenger airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Removal/installation of the spiral cable with sensor sub-assembly	Steering angle neutral point (Initialize parking assist monitor system) Steering angle setting	Parking assist monitor system (w/ Parallel Parking Assist Function)	Click here for Initialization Click here for Calibration
		Parking assist monitor system (w/o Parallel Parking Assist Function)	Click here for Initialization Click here for Calibration
	Steering angle neutral point (Initialize panoramic view monitor system)	Panoramic view monitor system	Click here for Initialization Click here for Calibration
	Steering angle neutral point (Initialize intelligent clearance sonar system)	Intelligent clearance sonar system	Click here
Disconnect cable from negative battery terminal	Memorize steering angle neutral point	LKA /LDA system	Click here
		Intelligent clearance sonar system*1
		Pre-crash safety system
		Lighting system (EXT) Cornering lights
		Adaptive high beam system
	Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	Parking assist monitor system (w/ Parallel parking assist function)	Click here
		Parking assist monitor system (w/o Parallel parking assist function)	Click here
		Panoramic view monitor system	Click here
	Initialize back door lock	Power door lock control system	Click here
	Reset back door close position	Power back door system	Click here

*1: When performing learning using the GTS.

Click here

PROCEDURE

PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE FRONT NO. 2 CONSOLE BOX INSERT

Click here
DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
1. Check that the engine switch is off.
2. Check that the cable is disconnected from the negative (-) battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3. *a Slider
  
  Slide the slider to release the lock, and then disconnect the connector.
  
  Note
  
  When disconnecting any airbag connector, take care not to damage the airbag wire harness.
REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here
REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
CAUTION:

When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.

Deployment Side
1. Remove the 2 screws.
2. Lean the instrument panel safety pad sub-assembly and disengage the 3 hooks.
3. Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.

REMOVE NO. 2 INSTRUMENT PANEL WIRE

*a	Protective Tape
*b	Airbag Connector
*c	Airbag Connector Lock
	Wire Harness Clamp

Disengage the clamp.

Separate the No. 2 instrument panel wire from the wire harness clamp.
Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.
Disconnect the 2 airbag connectors to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

Note

When disconnecting any airbag connector, take care not to damage the airbag wire harness.