TELEMATICS SYSTEM(w/ Telematics Transceiver except G-BOOK), Diagnostic DTC:B1583

DTC Code DTC Name
B1583 GPS Signal Unreceived

DESCRIPTION

This DTC is stored when GNSS satellite signals is not received for 30 km.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1583 GPS Signal Unreceived GNSS signals are not received for 30 km.

  • Telematics transceiver

  • Telephone antenna assembly

  • Wire harness or connector (No. 2 floor wire)

  • No. 3 antenna cord sub-assembly

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click here

PROCEDURE


  1. MOVE VEHICLE


    1. If the vehicle is outside the communication service area, move the vehicle into a communication service area, wait for a while and perform the operation again.

      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK DTC


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG) and wait for 20 seconds.

    4. Turn the GTS on.

    5. Check for DTCs and check that no DTCs are output.

      Click here

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  3. CHECK OPTIONAL COMPONENTS


    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result
      Result Proceed to
      Optional components are not installed A
      Optional components are installed B

      Note

      Do not remove optional components without the permission of the customer.


    B

    REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

    A

  4. CHECK DTC OUTPUT


    1. Clear the DTCs.

      Click here

    2. Recheck for DTCs and check if the same DTC is output again.

      Result
      Result Proceed to
      No DTCs are output. A
      DTC B1583 is output. B

    A

    END

    B

  5. INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. Remove the No. 3 antenna cord sub-assembly.

      Click here

    2. A01W2M4C08
      *a

      Component without harness connected

      (No. 3 Antenna Cord Sub-assembly)
      A01W0VYC20
      *a

      Component without harness connected

      (No. 3 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below. (excepf Glass Roof)

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-3 - B-4 Always Below 1 Ω
      A-3a - B-4a Always Below 1 Ω
      A-3 or B-4 - Body ground Always 10 kΩ or higher
      A-3a or B-4a - Body ground Always 10 kΩ or higher
    3. A01W2M4C08
      *a

      Component without harness connected

      (No. 3 Antenna Cord Sub-assembly)
      A01VZQOC07
      *a

      Component without harness connected

      (No. 3 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below. (for Glass Roof)

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-3 - C-3 Always Below 1 Ω
      A-3a - C-3a Always Below 1 Ω
      A-3 or C-3 - Body ground Always 10 kΩ or higher
      A-3a or C-3a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  6. INSPECT INSTRUMENT PANEL WIRE

    Result
    Proceed to
    OK
    NG

    1. Disconnect the Q34 and Q30 No. 2 floor wire connectors.

    2. A01W0NYC05
      *a

      Front view of No. 2 floor wire connector

      (to Telematics Transceiver)
      A01VZQOC13
      *a

      Front view of No. 2 floor wire connector

      (to No. 3 Antenna Cord Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q34-1 (TEL) - Q30-3 Always Below 1 Ω
      Q34-1a - Q30-3a Always Below 1 Ω
      Q34-1 (TEL) or Q30-3 - Body ground Always 10 kΩ or higher
      Q34-1a or Q30-3a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE INSTRUMENT PANEL WIRE

    OK

  7. REPLACE TELEPHONE ANTENNA ASSEMBLY


    1. Replace the telephone antenna assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here

    3. Recheck for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  8. REPLACE TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM REGISTRATION Click here