FRONT DOOR WINDOW FRAME MOULDING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door window frame moulding removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Disconnect cable from negative (-) battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	for 8GR-FKS: Click here for V35A-FTS: Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize Rear Door Sunshade System	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
Front door glass sub-assembly LH Front door glass sub-assembly RH Front door glass run LH Front door glass run RH	Initialize power window control system	Auto up and down function Jam protection function Catch protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Window open warning function	Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
When removing the front door glass sub-assembly LH, move the front door glass sub-assembly LH to the lowest position before disconnecting the battery negative (-) terminal.

PROCEDURE

PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 8GR-FKS:

Click here

for V35A-FTS:

Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE FRONT DOOR TRIM UPPER COVER LH

Click here
REMOVE FRONT DOOR ARMREST COVER LH

Click here
REMOVE FRONT DOOR NO. 2 ARMREST COVER LH

Click here
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Click here
REMOVE FRONT DOOR TRIM COVER LH

Click here
REMOVE UPPER DOOR FRAME GARNISH LH

Click here
REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP LH

Click here
REMOVE FRONT DOOR VENT SEAL LH

Click here
REMOVE FRONT DOOR SERVICE HOLE COVER LH

Click here
REMOVE FRONT DOOR NO. 3 WEATHERSTRIP LH

Click here
REMOVE FRONT DOOR NO. 2 WEATHERSTRIP LH

Click here
REMOVE FRONT DOOR BELT MOULDING LH

Click here
REMOVE FRONT DOOR REAR BELT MOULDING END COVER LH

Click here
REMOVE FRONT DOOR WINDOW FRAME MOULDING LH(CENTER PILLAR SIDE)
1. Remove the 3 nuts.
2. Protective Tape
  
  Put protective tape around the front door window frame moulding LH (center pillar side).
3. Remove in this Direction (1)
  
  Remove in this Direction (2)
  
  Detach the clip and guide and remove the front door window frame moulding LH (center pillar side) as shown in the illustration.
REMOVE FRONT PILLAR UPPER COVER SUB-ASSEMBLY LH

Click here
REMOVE FRONT DOOR GLASS RUN LH

Click here
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Click here
REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

Click here
REMOVE FRONT DOOR REAR WINDOW FRAME LH

Click here

REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH

Insert a 4.0 mm (0.157 in.) drill bit into a drill.

Tape

Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement

Area	Measurement
A	5.0 mm (0.197 in.)

Note

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.
Note
- Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
- Prying the rivets with the drill may damage the rivet installation holes or drill bit.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Detach the clip and remove the front door upper window frame moulding LH from the door frame.

REMOVE FRONT DOOR NO. 3 GLASS RUN LH
1. Remove the clip.
2. Detach the guide.
3. Remove in this Direction
  
  Detach the guide and remove the front door No. 3 glass run LH from the front door upper window frame moulding LH.
REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING LH
1. Remove the 2 clips and the front door front window frame moulding LH.

	Remove in this Direction (1)
	Remove in this Direction (2)