REAR DOOR BELT MOULDING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door belt moulding removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS:

Click here

for V35A-FTS:

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize Rear Door Sunshade System Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

Rear multiplex network door ECU LH or rear multiplex network door ECU RH is the connectors are disconnected Initialize rear door sunshade system The rear door sunshade system does not operate

Click here


  • Rear door glass sub-assembly LH

  • Rear door glass sub-assembly RH

  • Rear door glass run LH

  • Rear door glass run RH

 Initialize power window control system

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When removing the rear door glass sub-assembly LH, move the rear door glass sub-assembly LH to the lowest position before disconnecting the battery negative (-) terminal.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    B006BC1

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    for 8GR-FKS:

    Click here

    for V35A-FTS:

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE REAR DOOR TRIM UPPER COVER LH

    Click here

  5. REMOVE REAR DOOR ARMREST COVER LH

    Click here

  6. REMOVE REAR DOOR NO. 2 ARMREST COVER LH

    Click here

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  8. REMOVE REAR DOOR TRIM COVER LH

    Click here

  9. REMOVE REAR DOOR NO. 2 FRAME GARNISH LH

    Click here

  10. REMOVE REAR DOOR FRAME GARNISH LH

    Click here

  11. REMOVE CURTAIN RAIL SIDE COVER LH (w/ Rear Door Sunshade)

    Click here

  12. REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)

    Click here

  13. REMOVE REAR SIDE WINDOW COVER LH (w/ Rear Door Sunshade)

    Click here

  14. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP LH

    Click here

  15. REMOVE REAR MULTIPLEX NETWORK DOOR ECU LH

    Click here

  16. REMOVE REAR DOOR SERVICE HOLE COVER LH

    Click here

  17. REMOVE REAR DOOR FRONT BELT MOULDING END COVER LH

    Click here

  18. REMOVE REAR DOOR REAR BELT MOULDING END COVER LH

    Click here

  19. REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH

    Click here

  20. REMOVE REAR DOOR WINDOW FRAME MOULDING LH(CENTER PILLAR SIDE)

    Click here

  21. REMOVE REAR DOOR WINDOW FRAME MOULDING LH(REAR PILLAR SIDE)

    Click here

  22. REMOVE REAR DOOR OUTSIDE MOULDING INSERT LH

    Click here

  23. REMOVE REAR DOOR BELT MOULDING LH


    1. B006E79C01
      B006GBM Protective Tape

      Put protective tape around the rear door belt moulding LH.

    2. B006CHHC01
      B006DHE Remove in this Direction

      Detach the claw and guide and remove the rear door belt moulding LH.

  24. REMOVE REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY LH

    Click here

  25. REMOVE REAR DOOR GLASS RUN LH

    Click here

  26. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  27. REMOVE REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH

    Click here

  28. REMOVE REAR DOOR REAR WINDOW FRAME LH

    Click here

  29. REMOVE REAR DOOR BELT MOULDING SUB-ASSEMBLY LH

    Click here