FUEL TANK(for Rear Heated Oxygen Sensor) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point LKA/LDA System

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking Assist Monitor System (w/ Parallel Parking Assist Function)

Click here

Parking Assist Monitor System (w/o Parallel Parking Assist Function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Rear wheel alignment adjustment

  1. Clear zero point calibration data and system information.

  2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  • VSC disabled or malfunctions

  • DTCs are stored

  • Slip indicator light illuminates

  • ABS warning light illuminates

  • Theft deterrent system (tilt sensor)*1

Click here

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (w/ Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here

Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (w/o Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here


  • Parking assist ECU initialization

  • Adjust steering angle

 Panoramic view monitor system

for Initialization: Click here

for Calibration: Click here

Initialize headlight ECU sub-assembly LH

  • Adaptive high beam system

  • Automatic headlight beam level control system

Click here

Rear height control sensor sub-assembly Initialize headlight ECU sub-assembly LH

  • Adaptive High Beam System

  • Automatic headlight beam level control system

Click here

Gas leak from exhaust system is repaired Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here

*1: w/ TFT Meter Type

PROCEDURE


  1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

    Click here

  2. DRAIN FUEL

  3. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (for 2WD)

    Click here

  4. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY (for AWD)

    Click here

  5. REMOVE FRONT CENTER FLOOR COVER


    1. B007Z5RC03
      B007WXX Screw
      B00803L Nut

      Remove the 2 screws and nut.

    2. Disengage the 4 clips to remove the front center floor cover.

  6. REMOVE CHARCOAL CANISTER PROTECTOR

    Click here

  7. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    1. B007XIO

      Remove the 4 clips, 7 nuts and No. 1 fuel tank protector sub-assembly.

  8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. B007ZGC

      Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

      Click here

  9. DISCONNECT FUEL TANK BREATHER TUBE


    1. B007Z5G

      Loosen the clamp, then disconnect the fuel tank breather tube from the fuel tank filler pipe assembly.

  10. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    1. B007Y6X

      Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank filler pipe assembly.

  11. REMOVE FUEL TANK ASSEMBLY

    CAUTION:

    The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.

    B007ZSO

    1. B007XOJ

      Disconnect the fuel cut off valve with tube assembly from the charcoal canister assembly.

      Click here

    2. B007XZ4

      Remove the bolt, nut and rear fuel tank bracket LH.

    3. B00804V

      Remove the nut.

    4. B007XQX

      Support the fuel tank assembly using an engine lifter.

      Tech Tips

      Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.

    5. Remove the 4 bolts, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH.

    6. Lower the engine lifter to remove the fuel tank assembly.

      Note


      • Be careful not to drop the fuel tank assembly.

      • When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.

  12. REMOVE REAR FUEL TANK SIDE PLATE


    1. B007ZLU

      Remove the fuel tank cushion and rear fuel tank side plate from the fuel tank assembly.

  13. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. B007YYIC01
      *1 Fuel Tank Main Tube Sub-assembly

      Disengage the 3 claws to remove the fuel tank main tube sub-assembly from the fuel tank assembly.

  14. REMOVE FUEL TANK TO FILLER PIPE HOSE


    1. B007ZVH

      Loosen the clamp, then remove the fuel tank to filler pipe hose from the fuel tank assembly.

  15. REMOVE FUEL TANK CUSHION SET


    1. B007XQ3C01
      *1 Fuel Tank Cushion Set
      *2 No. 5 Fuel Tank Cushion

      Remove the 2 fuel tank cushion sets and 2 No. 5 fuel tank cushions from the fuel tank assembly.

  16. REMOVE TANK SUCTION TUBE SUPPORT


    1. B007Z57

      Remove the tank suction tube support from the fuel tank assembly.