Note
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during headlight ECU sub-assembly LH removal/installation are shown below.
Performed Work or System Condition | Necessary Procedures | Proceed to |
---|---|---|
Replacement of the headlight ECU sub-assembly LH | Synchronize the vehicle information | SYNCHRONIZE VEHICLE INFORMATION |
Perform headlight ECU sub-assembly LH initialization | HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION | |
Replacement of the rear height control sensor sub-assembly RH, removal and reinstallation of the rear height control sensor sub-assembly RH, replacement of the suspension, etc. have been performed. | Perform headlight ECU sub-assembly LH initialization | HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION |
Battery terminal is disconnected and connected. | Steering sensor zero point calibration |
If the steering sensor zero point calibration is not performed, the adaptive high beam system and cornering lights may not operate correctly.
A new headlight ECU sub-assembly LH cannot operate until the synchronize the vehicle information.
After replacing the headlight ECU sub-assembly LH, it is necessary to perform synchronize the vehicle information and initialization.
Even if the headlight ECU sub-assembly RH is replaced with a new one, synchronize the vehicle information and initialization are not necessary.
Adjust the headlight aim after initializing the headlight ECU sub-assembly LH.
When a malfunction is detected in the automatic headlight beam level control system, rear height control sensor sub-assembly RH signal initialization is impossible. Perform troubleshooting before initialization.
SYNCHRONIZE VEHICLE INFORMATION
When using the GTS:
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and check that "Headlight System Uninitialized Visit Your Dealer" warning message is displayed on the multi-information display.
Enter the following menus: Body Electrical / HL AutoLeveling*1 or AFS*2 / Utility / ECU Information Sync.
*1: for Single Beam Headlight
*2: for Triple Beam Headlight
Tester Display |
---|
ECU Information Sync |
Tester Display |
---|
ECU Information Sync |
Check the display on the GTS and press "Next".
Check that the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display continuously blinks 6 times at 2 Hz.
Press "Exit" and turn the engine switch off.
Note
After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.
Tech Tips
If the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display does not start blinking after performing step (v), perform the procedure again.
If the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display changes from blinking to illuminated, the rear height control sensor sub-assembly RH may be malfunctioning.
When not using the GTS:
Turn the engine switch on (IG) and check that "Headlight System Uninitialized Visit Your Dealer" warning message is displayed on the multi-information display.
Using the headlight dimmer switch, turn the low beam headlights on and off 8 times within 20 seconds after turning the engine switch on (IG).
Note
If the low beam headlights illuminate when the engine switch is on (IG), shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch. (w/o Light Control Switch OFF Position)
Tech Tips
If this step cannot be completed within 20 seconds, turn the engine switch off. Then, turn the engine switch on (IG) and restart the procedure.
Check that the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display continuously blinks 6 times at 2 Hz.
Tech Tips
If the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display does not start blinking after performing step (ii), perform the procedure again.
If the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display changes from blinking to illuminated, turn the engine switch off and then on (IG). If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed 5 seconds or more after the engine switch was turned on (IG), the rear height control sensor sub-assembly RH may be malfunctioning.
Turn the engine switch off.
Note
After synchronizing the vehicle information, initialize the headlight ECU sub-assembly LH.
HEADLIGHT ECU SUB-ASSEMBLY LH INITIALIZATION
Prepare vehicle for initialization
Unload the vehicle, ensuring that the spare tire, tools and jack are in their original positions.
Check that there are no occupants in the vehicle.
Turn the light control switch to the off position.
Stop the vehicle on a level surface and keep the vehicle height unchanged.
Check the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.
Turn the engine switch on (IG), and check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.
Initialization (When using the GTS)
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Enter the following menus: Body Electrical / HL AutoLeveling*1 or AFS*2 / Utility / Height Sensor Initialization.
*1: for Single Beam Headlight
*2: for Triple Beam Headlight
Tester Display |
---|
Height Sensor Initialization |
Tester Display |
---|
Height Sensor Initialization |
Check the display on the GTS and press "Next".
*A | Fuel Receiver Gauge (for Optitron Meter Type) |
*B | Fuel Receiver Gauge (for TFT Meter Type) |
Check the proper "Position ID" by the fuel level according to the table below.
Tech Tips
The "Position ID" is determined by the present fuel level as shown below.
Fuel Level | Position ID | Number of Times Headlight Leveling Warning Blinks |
---|---|---|
Within A range | EMPTY | 1 |
Within B range | 1/4 to over EMPTY | 2 |
Within C range | 1/2 to over 1/4 | 3 |
Within D range | 3/4 to over 1/2 | 4 |
Within E range | FULL to over 3/4 | 5 |
Select the proper "Position ID" and press "Next".
Press "Exit".
Check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.
Tech Tips
*: The number of times that "Headlight System Malfunction Visit Your Dealer" warning message blinks is determined by the "Position ID" selected.
If initialization does not finish normally, restart the initialization procedure from step (i).
If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the multi-information display, the headlight ECU sub-assembly LH may be malfunctioning.
Check that initialization finishes normally and turn the engine switch off.
Initialization (When not using the GTS)
Turn the engine switch on (IG).
*A | Fuel Receiver Gauge (for Optitron Meter Type) |
*B | Fuel Receiver Gauge (for TFT Meter Type) |
Check the specified number of times to turn the low beam headlights on and off.
Tech Tips
The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.
Fuel Level | Number of Times to Turn Low Beam Headlights On and Off |
---|---|
Within A range | 1 |
Within B range | 2 |
Within C range | 3 |
Within D range | 4 |
Within E range | 5 |
Enter initialization mode. (w/ Light Control Switch OFF Position)
Turn the engine switch and headlight dimmer switch off.
Cover the automatic light control sensor with a lightproof object.
Perform the following steps within 5 seconds.
Press the engine switch 2 times.
Tech Tips
Turn the engine switch on (IG).
While pulling the headlight dimmer switch, turn it from off to AUTO to off again 3 times or more.
Tech Tips
Check that the clearance lights turn from off to on and back off again.
Turn the headlight dimmer switch off.
Tech Tips
Perform the above operation within 5 seconds.
When initialization mode has been entered, "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display starts blinking at 1 Hz.
Enter initialization mode. (w/o Light Control Switch OFF Position)
Turn the engine switch and headlight dimmer switch off.
Shine a light on the automatic light control sensor.
Perform the following steps within 5 seconds.
Press the engine switch 2 times.
Tech Tips
Turn the engine switch on (IG).
While pulling the headlight dimmer switch, turn it from AUTO to TAIL to AUTO again 3 times or more.
Tech Tips
Check that the clearance lights turn from off to on and back off again.
Turn the headlight dimmer switch off.
Tech Tips
Perform the above operation within 5 seconds.
When initialization mode has been entered, "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display starts blinking at 1 Hz.
After entering initialization mode, turn the low beam headlights from off to on and back off again N* times.
Tech Tips
*: The number of times to turn the headlight dimmer switch assembly on and off (N) is determined by the fuel level of the fuel receiver gauge.
Turn the headlight dimmer switch on and off within 20 seconds of entering initialization mode.
Turn the headlight dimmer switch on and off at intervals of approx. 3 seconds.
Check the condition of the "Headlight System Malfunction Visit Your Dealer" warning message on the multi-information display.
Tech Tips
*: The number of times that "Headlight System Malfunction Visit Your Dealer" warning message blinks is determined by the number of times the low beam headlights are turned on and off.
If initialization does not finish normally, restart the initialization procedure from step (i).
If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the multi-information display, the headlight ECU sub-assembly LH may be malfunctioning.
Check that initialization finishes normally and turn the engine switch off.