Ремонт автомобилей Тойота в Москве, район метро МарьиноРемонт автомобилей Тойота в Москве, район метро МарьиноРемонт автомобилей Тойота в Москве, район метро Марьино
Проекты
Разделы
Электросхемы Toyota/Lexus

- USA

-- TOYOTA

--- TOYOTA 2012-2019 Avanza Electrical Wiring Diagram (EM19Y0E)

---- EM19Y0E_201609

----- System

------ Vehicle Interior

------- SRS (From Aug. 2015 Production) (201508 - )

 DLC3 Junction Connector Airbag Squib (Instrument Panel Passenger Airbag Assembly) Spiral Cable Sub-Assembly , Driver Side Squib Circuit (Horn Button Assembly) Junction Connector Spiral Cable Sub-Assembly , Driver Side Squib Circuit (Horn Button Assembly) Combination Meter Assembly Junction Connector Front Airbag Sensor LH Junction Connector Front Airbag Sensor RH Front Seat Outer Belt Assembly RH Front Seat Outer Belt Assembly LH ECM Airbag ECU Assembly d=" M 756.37, 589.89 L 756.37, 622.18 d=" M 832.86, 562.69 L 832.86, 622.18 d=" M 900.85, 562.69 L 900.85, 630.68 L 1223.80, 630.68 L 1223.80, 469.21 d=" M 909.35, 290.17 L 909.35, 254.76 d=" M 909.35, 197.25 L 909.35, 239.75 d=" M 943.34, 428.70 L 943.34, 376.29 15 ACL DLC3 E12 19 8 9 1 20 12 E87 Junction Connector P+ P- 1 2 Airbag Squib (Instrument Panel Passenger Airbag Assembly) E61 2 C 1 C Driver Side Squib Circuit (Horn Button Assembly) z5(C) 6 E39 Junction Connector D+ D- 1 B 2 B Spiral Cable Sub-Assembly E63(B),z5(C) CAN IC +B IG E SRS CANH CANL CPU 9 8 3 7 5 Combination Meter Assembly E34 9 Junction Connector E39 2 SLH+ 1 SLH- A26 Front Airbag Sensor LH 12 5 Junction Connector E86 2 SRH+ 1 SRH- A25 Front Airbag Sensor RH D- D+ Pretensioner 1 2 Front Seat Outer Belt Assembly RH J13 P- P+ Pretensioner 1 2 Front Seat Outer Belt Assembly LH J14 5A ECU IG2 1 2 (IG) 25 25 25 A F C HCAN 26 26 26 C A F LCAN ECM A24(A),A37(C),A38(F) 4 B PR- 22 A AP+ 3 B PR+ 21 A AP- 14 A FSS+ 18 A E1 28 A CANH 15 A FSS- 27 A CANL 16 A SL+ 10 A IG1 11 A ACL 17 A SL- 19 A D+ 20 A D- 5 B PL- 6 B PL+ E76(A),J18(B) Airbag ECU Assembly 5 5A BACK UP2 3J (BAT) (IG) 3H 7.5A ECU-IG1 5 CANH CANL Main Body ECU CANL CANH 3G 16 3G 17 3C 21 3C 30 10 3 1 9 2 4 3 5 4 1 (*1) (*2) (*3) * 1 :Before Dec. 2016 Production * 3 :From Apr. 2017 Production * 2 :From Dec. 2016 Production until Apr. 2017 Production B Y-G Y-B Y-R Y-B B W R L B W R G Y-R Y-B Y-B Y-G P G BR B R W-B BR P-B P L Y GR Y W P W W P W BE W GR NOTICE : When inspecting or repairing the SRS, perform service in accordance with the following precautionary instructions and the procedure, and precautions in the Repair Manual applicable for the model year. * Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of information when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting the battery. * Work must be started more than 90 seconds after the ignition or starter switch assembly is turned to the "LOCK"position and the negative (-) terminal cable is disconnected from the battery. (The SRS is equipped with a back-up power source so that if work is started within 90 seconds from disconnecting the negative (-) terminal cable of the battery, the SRS may deploy.) * When the negative (-) terminal cable is disconnected from the battery, the memory of the clock and audio system will be cleared. So before starting work, make a record of the contents in the audio memory system. When work is finished, reset the audio systems as they were before and adjust the clock. Some vehicles have power tilt steering, power telescopic steering, power seat and power outside rear view mirror which are all equipped with memory function. However, it is not possible to make a record of these memory contents. So when the work is finished, it will be necessary to explain it to your customer, and ask the customer to adjust the features and reset the memory. To avoid erasing the memory in each system, never use a back-up power supply from outside the vehicle. Before repair, remove the airbag sensor if shocks are likely to be applied to the sensor during repair. * * Do not expose the following parts directly to hot air or flame; * Never use SRS parts from another vehicle. When replacing parts, replace with new parts. Even in cases of a minor collision where the SRS does not deploy, the following parts should be inspected; * For the purpose of reuse, never disassemble and repair the following parts. * If the following parts have been dropped, or have cracks, dents and other defects in their case, bracket, and connector, replace with new one. * Use a volt/ohmmeter with high impedance (10 kΩ/V minimum) for troubleshooting electrical circuits of the system. * * Information labels are attached to the periphery of the SRS components. Follow the instructions of the notice. * After work on the SRS is completed, check the SRS warning light. * If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the Repair Manual. * Steering wheel pad * Front passenger airbag assembly * Seat belt pretensioner * Center airbag sensor assembly * Front airbag sensor assembly EE3 EE3 AE7 EE3 AE7 EE3 AE7 EE3 AE7 AE6 E4 E4
zatonevkredit.ru - 2024 - Авторский блог
Политика конфиденциальности