REAR AIR CONDITIONING UNIT REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear air conditioning unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/ Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Removal/installation of the spiral cable with sensor sub-assembly

  • Steering angle neutral point (Initialize parking assist monitor system)

  • Steering angle setting

 Parking assist monitor system (w/ Parallel parking assist function)

Click here for Initialization

Click here for Calibration
Parking assist monitor system (w/o parallel parking assist function)

Click here for Initialization

Click here for Calibration
Steering angle neutral point (Initialize panoramic view monitor system) Panoramic view monitor system

Click here for Initialization

Click here for Calibration
Steering angle neutral point (Initialize intelligent clearance sonar system) Intelligent clearance sonar system

Click here


  • Rear No. 1 cooling unit damper servo sub-assembly

  • Rear No. 2 cooling unit damper servo sub-assembly

 Initialize servo motor (Air conditioning system) DTCs are stored

Click here

*1: When performing learning using the GTS.
Click here Click here

Note

Make sure to select foot mode before removing the rear cooling unit assembly.

PROCEDURE


  1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

    Click here

  2. DRAIN ENGINE COOLANT

    Click here

  3. REMOVE NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR


    1. B007X53C02
      B007WXX Screw
      B00803L Grommet

      Remove the 2 screws and grommet.

    2. B007YXW

      Turn back the rear wheel house liner RH as shown in the illustration.

    3. B008006

      Remove the clip.

    4. B007Y9XC02
      B007WXX Clip
      B00803L Bolt

      Remove the 2 clips, bolt and No. 1 luggage compartment side cover protector.

  4. DISCONNECT AIR CONDITIONING HOSE AND ACCESSORY


    1. B007ZMZ

      Remove the bolt and rotate the hook connector as shown in the illustration.

    2. B007YWA

      Disconnect the suction tube.

    3. Remove the O-ring from the suction tube.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

    4. B007ZTL

      Disconnect the liquid tube.

    5. Remove the O-ring from the liquid tube.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

    6. B007WQK

      Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose.

      Note


      • Do not apply excessive force to the inlet heater water hose.

      • Prepare a drain pan or cloth in case the coolant leaks.

    7. B007ZTO

      Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose.

      Note


      • Do not apply excessive force to the outlet heater water hose.

      • Prepare a drain pan or cloth in case the coolant leaks.

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY

    Click here

  6. REMOVE REAR FLOOR FINISH PLATE

    Click here

  7. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  8. REMOVE REAR DOOR INSIDE SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  9. REMOVE REAR SEAT OUTER TRACK BRACKET COVER RH

    Click here

  10. REMOVE FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  11. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  12. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Click here

  13. REMOVE ROPE HOOK ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  14. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  15. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    Click here

  16. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  17. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  18. REMOVE REAR NO. 4 SIDE AIR DUCT


    1. B007ZQPC01
      B007Z37 Remove in this Direction (1)
      B007YXL Remove in this Direction (2)

      Remove the clip.

    2. Remove the rear No. 4 side air duct as shown in the illustration.

  19. REMOVE COOLER PLATE


    1. B007Z17

      Disengage the 2 claws to remove the cooler plate.

  20. REMOVE REAR NO. 3 SIDE AIR DUCT


    1. B007X2IC01
      B007Z37 Remove in this Direction

      Remove the clip.

    2. Remove the rear No. 3 side air duct as shown in the illustration.

  21. REMOVE REAR NO. 2 SIDE AIR DUCT


    1. B007YRLC01
      B007Z37 Remove in this Direction

      Disengage the clamp.

    2. Remove the clip.

    3. Remove the rear No. 2 side air duct as shown in the illustration.

  22. REMOVE REAR NO. 1 SIDE AIR DUCT


    1. B007ZLIC01
      B007Z37 Remove in this Direction

      Remove the clip.

    2. Remove the rear No. 1 side air duct as shown in the illustration.

  23. REMOVE REAR NO. 7 AIR DUCT


    1. B007ZUUC01
      B007Z37 Remove in this Direction

      Remove the clip.

    2. Remove the rear No. 7 air duct as shown in the illustration.

  24. REMOVE REAR NO. 6 AIR DUCT


    1. B007XP2C01
      B007Z37 Remove in this Direction

      Remove the clip.

    2. Remove the rear No. 6 air duct as shown in the illustration.

  25. REMOVE REAR NO. 5 AIR DUCT


    1. B007WZCC01
      B007Z37 Remove in this Direction (1)
      B007YXL Remove in this Direction (2)

      Remove the clip.

    2. Remove the rear No. 5 air duct as shown in the illustration.

  26. REMOVE REAR AIR CONDITIONING UNIT ASSEMBLY


    1. B007X39

      Disconnect each connector.

    2. Disengage each clamp.

    3. Disconnect the drain cooler hose.

      B007XKB

    4. Remove the 4 bolts.

    5. Disengage the guide and remove the rear air conditioning unit assembly.

  27. REMOVE REAR AIR DUCT (w/ Rear Air Duct)


    1. B007WSQ

      Remove the 3 screws and rear air duct.

  28. REMOVE WATER PIPE AND HOSE SUB-ASSEMBLY A


    1. B007ZUEC02
      B007WXX Bolt
      B00803L Screw

      Remove the bolt and screw.

    2. B007YW9

      Slide the 2 clips and disconnect the water pipe and hose sub-assembly A.

      Note


      • Do not apply excessive force to the water pipe and hose sub-assembly A.

      • Prepare a drain pan or cloth in case the coolant leaks.

  29. REMOVE NO. 1 COOLING UNIT PACKING


    1. B007XV6

      Remove the No. 1 cooling unit packing.

  30. REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY


    1. B007XBD

      Remove the bolt and rotate the hook connector as shown in the illustration.

    2. Remove the 3 screws and air conditioning tube and accessory assembly.

    3. Remove the 2 O-rings from the rear cooling unit expansion valve.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  31. REMOVE DRAIN COOLER HOSE


    1. B007Y7D

      Remove the drain cooler hose from the rear cooling unit assembly.