AIRBAG SYSTEM, Diagnostic DTC:B1825, B1826, B1827, B1828

DTC Code DTC Name
B1825 Short in Side Squib (LH) Circuit
B1826 Open in Side Squib (LH) Circuit
B1827 Short in Side Squib (LH) Circuit (to Ground)
B1828 Short in Side Squib (LH) Circuit (to +B)

DESCRIPTION

The front side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1825 Short in Side Squib (LH) Circuit

  • The airbag sensor assembly detects a line short in the front side squib LH circuit during the primary check.

  • Front side squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front side squib LH (Front seat airbag assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode
B1826 Open in Side Squib (LH) Circuit

  • The airbag sensor assembly detects an open in the front side squib LH circuit.

  • Front side squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front side squib LH (Front seat airbag assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode
B1827 Short in Side Squib (LH) Circuit (to Ground)

  • The airbag sensor assembly detects a short to ground in the front side squib LH circuit.

  • Front side squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front side squib LH (Front seat airbag assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode
B1828 Short in Side Squib (LH) Circuit (to +B)

  • The airbag sensor assembly detects a short to B+ in the front side squib LH circuit.

  • Front side squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front side squib LH (Front seat airbag assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode

WIRING DIAGRAM

B0087OIE78
*a Front Side Squib LH (Front Seat Airbag Assembly LH)
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

Tech Tips


  • Perform the simulation method by selecting check mode (Signal Check) using the GTS.

    Click here

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

    Click here

PROCEDURE


  1. CHECK CONNECTORS


    1. B0084X5C01
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the front seat airbag assembly LH and airbag sensor assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the front seat airbag assembly LH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

      OK
      The short springs are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK FRONT SEAT AIRBAG ASSEMBLY LH


    1. B0088AYC27
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *a

      Front view of wire harness connector

      (to Front Seat Airbag Assembly LH)

      Connect the connector to the airbag sensor assembly.

    2. Connect SST (resistance 2.1 Ω) to connector C.

      CAUTION:

      Never connect a tester to the front seat airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting it.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs.


      Body Electrical > SRS Airbag > Trouble Codes
      OK
      DTC B1825, B1826, B1827 or B1828 is not output.

      Tech Tips

      Codes other than DTCs B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Disconnect SST from connector C.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT SEAT AIRBAG ASSEMBLY LH Click here

    NG

  3. CHECK FLOOR WIRE


    1. B0089K5C45
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Seat Airbag Assembly LH)

      Disconnect the floor wire from the airbag sensor assembly.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        R49-1 (SFL+) - Body ground Ignition switch ON Below 1 V
        R49-2 (SFL-) - Body ground Ignition switch ON Below 1 V

      4. Turn the ignition switch off.

      5. Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check for an open in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R49-1 (SFL+) - R49-2 (SFL-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R49-1 (SFL+) - Body ground Always 1 MΩ or higher
        R49-2 (SFL-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B.

        Click here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R49-1 (SFL+) - R49-2 (SFL-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK DTC


    1. B008713C01
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory.


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.


      Body Electrical > SRS Airbag > Trouble Codes
      OK
      DTC B1825, B1826, B1827 or B1828 is not output.

      Tech Tips

      Codes other than DTCs B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.

      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here