BACK WINDOW GLASS REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the back window glass removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic View Monitor System

Click here

Initialize Rear Door Sunshade System Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

*: When performing learning using the GTS.
Click here Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    Click here

    B006BC1

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal.

      Click here

      CAUTION:


      • After disconnecting the cable from the negative (-) battery terminal, wait for at least 90 seconds to start the operation.

      • If the airbag deploys for any reason, it may cause a serious accident.

      B006BY6

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

  4. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  5. REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY

    Click here

  6. REMOVE CENTER STOP LIGHT COVER LH

    Click here

  7. REMOVE CENTER STOP LIGHT COVER RH

    Click here

  8. REMOVE CENTER STOP LIGHT ASSEMBLY

    Click here

  9. REMOVE LOWER OUTSIDE BACK WINDOW MOULDING

    Click here

  10. REMOVE BACK WINDOW GLASS

    Note

    The back window glass may fall while performing this procedure. Therefore, use suction cups to hold the back window glass from the outside of the vehicle. The back window glass may fall while performing this procedure. Therefore, use suction cups to hold the back window glass from the outside of the vehicle.


    1. Disconnect each connector.

    2. B006E8IC01
      B006GBM Protective Tape

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    3. Using a knife, cut off the No. 1 back window moulding as shown in the illustration.

      Note


      • Do not damage the back window glass or body panel.

      • If the body panel is damaged, perform rust-prevention treatment after removing the back window glass.

      Tech Tips

      Use the same procedure for both upper outside back window moulding RH.

      B006EL3C03
      *a Cut Off - -

    4. When reusing the back window glass:


      1. B006CYOC01
        *a Matchmarks

        Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

      2. Install the suction cups to the back window glass.

    5. B006C8FC02
      *1 Back Window Glass Stopper
      *a Piano Wire

      From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

    6. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

      Note

      When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

    7. Cut through the adhesive by pulling the piano wire around the glass. (Leave the back window glass stopper)

      Note

      When working near the back window glass connector, be careful not to damage it with the piano wire.

    8. Using suction cups, disconnect the 2 back window glass stoppers and remove the back window glass.

      B006GVKC01
      *A for 1-piece Type *B for 2-piece Type
      *1 No. 1 Back Window Glass Stopper *2 No. 2 Back Window Glass Stopper

      Note

      Do not drop the back window glass.

  11. REMOVE NO. 1 BACK WINDOW MOULDING


    1. When reusing the back window glass:


      1. B006BTHC01
        *a Backside

        Using a gasket scraper, remove the No. 1 back window moulding from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the No. 1 back window moulding with a new one.

  12. REMOVE BACK WINDOW GLASS DAM KIT


    1. When reusing the back window glass:


      1. B0069IBC01
        *a Backside

        Using a gasket scraper, remove the back window glass dam kit from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the back window glass dam kit with a new one.

  13. REMOVE BACK WINDOW GLASS DAM KIT


    1. When reusing the back window glass:


      1. B006FH6C01
        *a Backside

        Using a gasket scraper, remove the 6 back window glass dam kits from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the back window glass dam kit with a new one.

  14. REMOVE WINDSHIELD GLASS SEAL


    1. When reusing the back window glass:


      1. B006G2SC01
        *a Backside

        Using a gasket scraper, remove the windshield glass seal from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the windshield glass seal with a new one.

  15. REMOVE CENTER STOP LIGHT BRACKET LH


    1. When reusing the back window glass:


      1. B006BC8C01
        *a Backside

        Using a gasket scraper, remove the center stop light bracket LH from the back window glass.

        Note

        Do not damage the back window glass.

  16. REMOVE CENTER STOP LIGHT BRACKET RH


    1. When reusing the back window glass:


      1. B006BS9C01
        *a Backside

        Using a gasket scraper, remove the center stop light bracket RH from the back window glass.

        Note

        Do not damage the back window glass.

  17. REMOVE CENTER STOP LIGHT WIRE


    1. When reusing the back window glass:


      1. B0069LBC01
        *a Backside

        Using a gasket scraper, remove the center stop light wire from the back window glass.

        Note


        • Do not damage the back window glass.

        • Be sure to replace the center stop light wire with a new one.

  18. REMOVE NO. 1 BACK WINDOW GLASS STOPPER


    1. When reusing the back window glass:


      1. B006D1T

        for 1-piece Type:

        Using a gasket scraper, remove the 2 No. 1 back window glass stopper from the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the No. 1 back window glass stopper with a new one.

      2. B006BLW

        for 2-piece Type:

        Using a gasket scraper, remove the 2 No. 1 back window glass stoppers from the body.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the No. 1 back window glass stopper with a new one.

  19. REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    1. When reusing the back window glass:


      1. B006D1T

        Using a gasket scraper, remove the 2 No. 2 back window glass stoppers from the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the No. 2 back window glass stoppers with a new one.