REAR AIR CONDITIONING UNIT REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear cooling unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

Steering sensor (Including removal and installation) Steering angle neutral point Parking support brake system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Steering angle setting Parking assist monitor system

Click here

Panoramic view monitor system

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B006C5U

Note


  • If the rear seat cushion airbag assembly LH was deployed, replace the rear seat cushion panel LH, rear seat cushion pad and separate type rear seat cushion cover with the necessary parts in accordance with the extent of the collision damage.

  • If the rear seat airbag assembly LH was deployed, replace the rear seat sub panel sub-assembly LH, separate type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure as for the LHD and RHD vehicles.

  • The procedure listed below is for the LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    B006BC1

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.

    • SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the engine switch off and disconnecting the cable from the negative (-) battery terminal, SRS parts may deploy.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. DRAIN REFRIGERANT LINE

    Click here

  5. REMOVE REAR SEAT ASSEMBLY

    Click here

  6. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (for Power Seat)

    Click here

  7. REMOVE NO. 4 REAR AIR DUCT


    1. B006GCG

      Remove the No. 4 rear air duct.

  8. REMOVE NO. 5 REAR AIR DUCT


    1. B006B88

      Remove the No. 5 rear air duct.

  9. REMOVE NO. 2 ROOF SIDE AIR DUCT LH


    1. B006FVW

      Using a clip remover, detach the clip and pull the No. 2 roof side air duct LH out from the duct on the vehicle side.

  10. REMOVE NO. 2 ROOF SIDE AIR DUCT RH


    1. B006FMV

      Using a clip remover, detach the clip and pull the No. 2 roof side air duct RH out from the duct on the vehicle side.

  11. REMOVE NO. 6 REAR AIR DUCT


    1. B006EK3

      Using a clip remover, remove the clip.

    2. B006FJ6

      Lift the No. 6 rear air duct in the direction indicated by the arrow shown in the illustration.

    3. B006GH9

      Remove the No. 6 rear air duct in the direction indicated by the arrow shown in the illustration.

  12. REMOVE COOLING BOX ASSEMBLY (w/ Cool Box)

    Click here

  13. REMOVE LUGGAGE COMPARTMENT FLOOR MAT

    Click here

  14. REMOVE LUGGAGE COMPARTMENT TRIM BOX (w/o Air Suspension)

    Click here

  15. REMOVE TOOL BOX

    Click here

  16. REMOVE INNER LOWER LUGGAGE COMPARTMENT TRIM COVER

    Click here

  17. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  18. REMOVE LUGGAGE COMPARTMENT TRIM COVER RH

    Click here

  19. REMOVE ROPE HOOK ASSEMBLY

    Click here

  20. REMOVE REAR FLOOR FINISH PLATE

    Click here

  21. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER

    Click here

  22. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  23. REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER

    Click here

  24. REMOVE SIDE TRIM BOX

    Click here

  25. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH

    Click here

  26. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH

    Click here

  27. REMOVE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY


    1. B006AEHC01
      B006AHR Bolt
      B006EC9 Drain Hose

      Remove the bolt and disconnect the drain hose connection.

    2. B006EJVC01
      B006DHE Remove in this Direction

      Slightly moving the air conditioning tube and accessory assembly in the direction indicated by the arrow shown in the illustration, disconnect it from the rear cooling unit.

    3. Remove the 2 O-rings from the air conditioning tube and accessory assembly.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  28. REMOVE REAR COOLING UNIT ASSEMBLY


    1. B006D6N

      Disconnect the connector and detach the clamp.

    2. B006BYO

      Remove the 5 nuts.

    3. Detach the clip, protrusion and remove the rear cooling unit.