REAR SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL REAR SEAT OUTER BELT ANCHOR BRACKET ASSEMBLY


    1. Engage the guide and install the rear seat outer belt anchor bracket assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSPECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

    Click here

  3. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY


    1. B004FJSN01

      Engage the guide and temporarily install the rear seat 3 point type outer belt assembly with the 2 bolts.

    2. Fully tighten the bolt (A) first, then the bolt (B) to install the rear seat 3 point type outer belt assembly.

      Torque:
      Bolt (A)
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
      Bolt (B)
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. for LH Side:


      1. B004GAUC01
        *a Locking Button
        *b Lock

        Connect the pretensioner connector and lock the locking button as shown in the illustration.

        Note

        Securely lock the locking button.

    4. for RH Side:


      1. B004GQVC02
        *a Locking Button
        *b Lock

        Connect the pretensioner connector and lock the locking button as shown in the illustration.

        Note

        Securely lock the locking button.

    5. Check that the ELR locks.

      Note

      The check should be performed with the rear seat 3 point type outer belt assembly installed to the vehicle.


      1. With the rear seat 3 point type outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.

  4. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY

    Click here

  5. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

    Click here

  6. CONNECT FRONT SEAT OUTER BELT ASSEMBLY

    Click here

  7. INSTALL LAP BELT OUTER ANCHOR COVER

    Click here

  8. INSTALL REAR SEATBACK ASSEMBLY LH (for LH Side)

    Click here

  9. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)


    1. Install the rear seat headrest assembly.

  10. INSTALL REAR SEATBACK ASSEMBLY RH (for RH Side)

    Click here

  11. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  12. INSTALL REAR SIDE SEATBACK ASSEMBLY

    Click here

  13. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY


    1. B004G88C01
      *a Indented Part

      Connect the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type outer belt assembly to overlap the indented parts of the floor panel.

    2. B004FT2

      Engage the 3 clips to connect the belt guide unit of the rear seat 3 point type outer belt assembly.

  14. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  15. INSTALL REAR SEAT CUSHION ASSEMBLY

    Click here

  16. INSTALL FRONT DOOR SCUFF PLATE

    Click here

  17. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  18. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  19. INSPECT SRS WARNING LIGHT

    Click here