SMART ENTRY AND START SYSTEM (for Entry Function) Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly LH (trigger switch) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU [smart key ECU assembly] and front door outside handle assembly LH [front passenger door electrical key antenna]), or there may be wave interference.

WIRING DIAGRAM

B007P77E07

INSPECTION PROCEDURE

Note


  • The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

  • When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).

    While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution Click here.

  • After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

PROCEDURE


  1. CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. CHECK FOR DTC


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B27A2 is not output. A
      DTC B27A2 is output. B

    B

    Go to DTC B27A2 Click here

    A

  3. CHECK WAVE ENVIRONMENT


    1. B007QURE01
      Text in Illustration
      *a Approximately 0.3 m (0.984 ft.)

      Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly LH and perform an entry function check Click here.

      Note

      If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.

      Tech Tips

      If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result
      Result Proceed to
      Entry function does not operate normally A
      Entry function operates normally B

    B

    AFFECTED BY WAVE INTERFERENCE

    A

  4. READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Data List.

    5. According to the display on the GTS, read the Data List.

      Entry&Start
      Tester Display Measurement Item / Range Normal Condition Diagnostic Note
      P-Door Trigger Switch Front passenger door trigger switch / ON or OFF

      ON: Front passenger door trigger switch pressed

      OFF: Front passenger door trigger switch not pressed

      • Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).

      • Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate.
      OK
      On the GTS screen, the display changes between ON and OFF as shown in the table above.

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH AND BODY GROUND) Click here

    OK

  5. CHECK KEY DIAGNOSTIC MODE


    1. B007QURE01
      Text in Illustration
      *a 0.7 to 1 m (2.30 to 3.28 ft.)

      Check the following antennas in key diagnostic mode.

    2. Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

      Tech Tips

      If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


      1. Check the No. 1 indoor electrical key antenna assembly (front bumper LH):

        When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly LH, check that the wireless door lock buzzer sounds.

        OK
        Wireless door lock buzzer sounds.

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY) Click here

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  6. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY)


    1. Disconnect the B76 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the A41 No. 1 indoor electrical key antenna assembly (front bumper LH) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B76-6 (CLG2) - A41-1 (ANTE2) Always Below 1 Ω
      B76-23 (CG2B) - A41-2 (CLGB) Always Below 1 Ω
      B76-6 (CLG2) or A41-1 (ANTE2) - Body ground Always 10 kΩ or higher
      B76-23 (CG2B) or A41-2 (CLGB) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)


    1. Connect the A41 No. 1 indoor electrical key antenna assembly (front bumper LH) connector.

    2. Connect the B76 certification ECU (smart key ECU assembly) connector.

    3. Using an oscilloscope, check the waveform.

      B007VGKE06
      Text in Illustration
      *a

      Component with harness connected

      (Certification ECU [Smart Key ECU Assembly])

      		 *b Waveform 1
      *c Trigger switch ON - -
      OK
      Tester Connection Switch Condition Tool Setting Specified Condition
      B76-6 (CLG2) - B76-23 (CG2B)

      Procedure:


      1. Engine switch off

      2. All doors closed

      		 - Not pulse generation

      Procedure:


      1. Engine switch off

      2. All doors closed

      3. Press the trigger switch on the front door outside handle assembly LH

      		 2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)

    NG

    CHECK ENTRY DOOR LOCK OPERATION Click here

    OK

    REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT BUMPER LH) Click here

  8. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH AND BODY GROUND)


    1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the L6 front door outside handle assembly LH (trigger switch) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B75-12 (TSW2) - L6-1 Always Below 1 Ω
      L6-2 (TRG-) - Body ground Always Below 1 Ω
      B75-12 (TSW2) or L6-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH (TRIGGER SWITCH)


    1. Remove the front door outside handle assembly LH (trigger switch) Click here.

    2. Inspect the front door outside handle assembly LH (trigger switch) Click here.


    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH Click here

    OK

  10. CHECK ENTRY DOOR LOCK OPERATION


    1. Check the operation of the entry lock/unlock function Click here.

      Tech Tips

      Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly LH before performing the inspection.

      OK
      Entry lock/unlock operate normally.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

    END (CONNECT CONNECTORS PROPERLY)