FRONT DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door disassembly/reassembly are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here


  • Door window regulator assembly

  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B007XYL

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B007WSF

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. B007XXV

      Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug.

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)


    1. B007Y8N

      Using a moulding remover, disengage the 4 clips and 4 guides.

    2. Disconnect the connector to remove the multiplex network master switch assembly with front door upper armrest base panel.

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)


    1. B007YIL

      Using a moulding remover, disengage the 4 clips and 4 guides.

    2. Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.

  6. REMOVE DOOR ARMREST COVER


    1. B007YYL

      Remove the door armrest cover.

  7. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION


    1. B007Z1F

      Remove the screw and front door No. 1 stiffener cushion.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. B007ZC3C01
      B007ZL6 Protective Tape

      Apply protective tape to the front door panel as shown in the illustration.

    2. B007Y93

      Remove the 3 screws.

    3. B007ZHWC01
      B007Z37 Remove in this Direction

      Using a clip remover, disengage the 10 clips and remove the front door trim board sub-assembly as shown in the illustration.

    4. Disconnect each connector.

    5. B007XI8C01
      B007Z37 Remove in this Direction

      Disconnect the front door lock remote control cable assembly from the front door inside handle sub-assembly as shown in the illustration.

    6. B007XX8C01
      B007Z37 Remove in this Direction
      *a Push

      Disengage the 2 claws as shown in the illustration to disconnect the front door inside locking cable assembly and remove the front door trim board sub-assembly.

  10. REMOVE SEAT MEMORY SWITCH (w/ Memory)

    Click here

  11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. B007WUO

      Disengage the 6 claws and remove the front door inner glass weatherstrip as shown in the illustration.

  12. REMOVE FRONT DOOR AIR DUCT


    1. B007X07

      Remove the 4 screws.

    2. Disengage the guide to remove the front door air duct.

  13. REMOVE DOOR LOCK CONTROL KNOB BEZEL


    1. B007ZW0C01
      B007Z37 Remove in this Direction

      Disengage the 2 claws and remove the door lock control knob bezel as shown in the illustration.

  14. REMOVE FRONT DOOR TRIM POCKET


    1. B007XB8

      Remove the 8 screws and front door trim pocket.

  15. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY

    Click here

  16. REMOVE OUTER MIRROR PROTECTOR

    Click here

  17. REMOVE OUTER MIRROR INSTALL HOLE COVER

    Click here

  18. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

    Click here

  19. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  20. REMOVE FRONT DOOR NO. 1 TRIM BRACKET


    1. B007YR3

      Remove the 2 screws and front door No. 1 trim bracket.

  21. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. B007WZ1

      Disconnect the connector.

    2. Turn the front door weatherstrip clip 45 degrees and remove the 4 front door weatherstrip clips as shown in the illustration.

    3. B007WSR

      Disengage the 5 clamps.

    4. B00803R

      Disengage the 5 clips to remove the front door service hole cover.

  22. REMOVE DOOR SIDE AIRBAG SENSOR

    Click here

  23. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. B007WV2

      Remove the hole plug.

    2. for Driver Side:


      1. Connect the multiplex network master switch assembly.

    3. for Front Passenger Side:


      1. Connect the power window regulator switch assembly.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the engine switch on (IG).

    6. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    7. Turn the engine switch off.

    8. Disconnect the cable from the negative (-) battery terminal.

    9. for Driver Side:


      1. Disconnect the multiplex network master switch assembly.

    10. for Front Passenger Side:


      1. Disconnect the power window regulator switch assembly.

    11. B007WZZ

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass sub-assembly to fall.

    12. B008018C01
      B007Z37 Remove in this Direction (1)
      B007YXL Remove in this Direction (2)

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the front door glass sub-assembly.

  24. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. B007ZGK

      Disengage the 2 claws to remove the front door No. 2 service hole cover.

    2. B007Y8HC01
      *a Temporary Bolt

      Disconnect the connector.

    3. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.

    4. Remove the 5 bolts.

    5. Remove the front door window regulator assembly.

    6. Remove the temporary bolt from the front door window regulator assembly.

  25. REMOVE FRONT DOOR GLASS RUN


    1. B007XQB

      Remove the front door glass run.

  26. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. B007WS8C01
      B007Z37 Remove in this Direction

      Remove the 2 bolts.

    2. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.

  27. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. B007ZS2

      Disengage the clamp.

    2. Disengage the 2 claws.

    3. Using a screwdriver, disconnect the connector.

    4. B007ZRNC01
      B007Z37 Disengage in this Direction

      Disengage the 2 claws and move the lever as shown in the illustration.

    5. B007YO6C01
      B007Z37 Remove in this Direction

      Remove the front door outside handle assembly as shown in the illustration.

  28. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. B007XTN

      Remove the hole plug.

    2. B007Z4Z

      Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  29. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. B007YX8

      Remove the hole plug.

    2. B007X28

      Using a T30 "TORX" socket wrench, loosen the screw.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

    3. Disengage the 2 guides and claw to remove the front door outside handle cover.

  30. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    1. B007YPW

      Disengage the 3 claws to remove the front door front outside handle pad.

  31. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    1. B007X02

      Disengage the claw.

    2. B007ZOVC01
      B007Z37 Remove in this Direction (1)
      B007YXL Remove in this Direction (2)

      Disengage the 3 guides to remove the front door rear outside handle pad as shown in the illustration.

  32. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

    Click here

  33. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. B007YZGC01
      *A Inside
      *B Outside

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Slide the front door outside handle frame sub-assembly to disengage the claw and remove the front door outside handle frame sub-assembly.

  34. REMOVE FRONT DOOR LOCK OPEN ROD


    1. B007YXCC01
      B007Z37 Remove in this Direction (1)
      B007YXL Remove in this Direction (2)

      Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.

  35. REMOVE FRONT DOOR CHECK ASSEMBLY


    1. B007ZV3C01
      B007WXX Nut
      B00803L Bolt

      Remove the 2 nuts and bolt, and front door check assembly.

  36. REMOVE FRONT DOOR WEATHERSTRIP


    1. B00802BC01
      B007ZL6 Double-sided Tape

      Using a clip remover, disengage the 25 clips and remove the front door weatherstrip.

  37. REMOVE FRONT DOOR PANEL PROTECTOR


    1. B007ZRO

      Remove the front door panel protector.

  38. REMOVE FRONT DOOR VENT SEAL


    1. B007ZC4

      Remove the front door vent seal.

  39. REMOVE UPPER DOOR FRAME GARNISH


    1. B007YSW

      Disengage the 3 claws to remove the upper door frame garnish.

  40. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    1. B007ZR4C01
      B007WXX Bolt
      B00803L Screw

      Remove the 2 bolts, screw and front door front lower frame sub-assembly.

  41. REMOVE FRONT DOOR FIX WINDOW GLASS


    1. B007X23C02
      B007Z37 Remove in this Direction

      Remove the front door fix window glass with the front door fix window weatherstrip as shown in the illustration.

    2. Remove the front door fix window glass from the front door fix window weatherstrip.

  42. REMOVE FRONT DOOR PANEL CUSHION


    1. B007ZIH

      Disengage the claw to remove the front door panel cushion.

  43. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

    Click here

  44. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

    Click here

  45. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

    Click here

  46. REMOVE FRONT DOOR REAR OUTSIDE STRIPE

    Click here

  47. REMOVE FRONT DOOR STRIPE

    Click here

  48. REMOVE NO. 1 BLACK OUT TAPE

    Click here

  49. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

    Click here

  50. REMOVE FRONT DOOR SCUFF PLATE

    Click here

  51. REMOVE COWL SIDE TRIM BOARD

    Click here

  52. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING

    Click here