MULTI-DISPLAY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the multi-display assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure as for the RHD and LHD vehicles.
The procedure listed below is for the LHD vehicles.

PROCEDURE

PRECAUTION
CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
Note
- After replacing the radio receiver assembly, if the "New software is not compatible with the system. Contact your dealer." on-screen message is displayed on the multi-display, update the software of the navigation ECU.
- After replacing the navigation ECU, if the "New software is not compatible with the system. Contact your dealer." on-screen message is displayed on the multi-display, update the software of the radio receiver assembly.
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  
  Click here
- If the airbag deploys for any reason, it may cause a serious accident.
Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here
REMOVE INSTRUMENT SIDE PANEL LH

Click here
REMOVE INSTRUMENT SIDE PANEL RH

Click here
REMOVE LOWER NO. 1 INSTRUMENT PANEL PAD SUB-ASSEMBLY

Click here
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Click here
REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here
INSTALL INSTRUMENT PANEL SAFETY PAD INSERT SUB-ASSEMBLY

Click here
INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Click here
REMOVE MULTI-DISPLAY ASSEMBLY
1. Remove the 2 bolts.
2. Hold area 1 shown in the illustration and move it toward the rear of the vehicle to detach the clip.
  
  Place Hands Here Remove in this Direction
  
  Note
  
  If excessive force is applied to the multi-display assembly, it may become damaged.
  
  Tech Tips
  
  The top area of the instrument panel (a) can be easily detached by lifting it up slightly from the bottom as shown in the illustration.
3. While pulling towards the rear of the vehicle, detach the clip in the order shown in the illustration.
  
  Remove in this Direction - -
  
  Note
  
  If excessive force is applied to the multi-display assembly, it may become damaged.
4. Incline the multi-display assembly as shown in the illustration and remove it
  
  Remove in this Direction - -
  
  Note
  
  If excessive force is applied to the multi-display it may become damaged.
5. Detach the 2 clamps, disconnect each connector and remove the multi-display assembly.