REAR DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Replacement Part	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Removal and installation of battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize Rear Door Sunshade System	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here
Rear multiplex network door ECU LH Rear multiplex network door ECU RH Rear multiplex network door ECU LH or rear multiplex network door ECU RH is the connectors are disconnected	Initialize rear door sunshade system	The rear door sunshade system does not operate	Click here
Power window regulator motor assembly LH Power window regulator motor assembly RH Rear door window regulator assembly LH Rear door window regulator assembly RH Rear door glass sub-assembly LH Rear door glass sub-assembly RH Rear door glass run LH Rear door glass run RH Rear door No. 3 glass run LH Rear door No. 3 glass run RH	Initialize power window control system	Auto up and down function Jam protection function Catch protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Window open warning function	Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
When removing the rear door glass sub-assembly LH, move the rear door glass sub-assembly LH to the lowest position before disconnecting the battery negative (-) terminal.

PROCEDURE

PRECAUTION

Note

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here
REMOVE REAR DOOR TRIM UPPER COVER LH

Click here
REMOVE REAR DOOR ARMREST COVER LH

Click here
REMOVE REAR DOOR NO. 2 ARMREST COVERLH

Click here
REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Click here
REMOVE REAR DOOR TRIM COVER LH

Click here
REMOVE REAR DOOR NO. 2 FRAME GARNISH LH

Click here
REMOVE REAR DOOR FRAME GARNISH LH

Click here
REMOVE CURTAIN RAIL SIDE COVER LH (w/ Rear Door Sunshade)

Click here
REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)

Click here
REMOVE REAR SIDE WINDOW COVER LH (w/ Rear Door Sunshade)

Click here
REMOVE REAR DOOR GLASS INNER WEATHERSTRIP LH

Click here
REMOVE REAR DOOR FRONT BELT SEAL LH

Click here
REMOVE REAR DOOR REAR BELT SEAL LH

Click here
REMOVE REAR SPEAKER ASSEMBLY

Click here
REMOVE REAR MULTIPLEX NETWORK DOOR ECU LH

Click here
REMOVE REAR DOOR SERVICE HOLE COVER LH

Click here
REMOVE REAR DOOR FRONT BELT MOULDING END COVER LH

Click here
REMOVE REAR DOOR REAR BELT MOULDING END COVER LH

Click here
REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH

Click here
REMOVE REAR DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

Click here
REMOVE REAR DOOR WINDOW FRAME MOULDING LH (REAR PILLAR SIDE)

Click here
REMOVE REAR DOOR OUTSIDE MOULDING INSERT LH

Click here
REMOVE REAR DOOR BELT MOULDING LH

Click here
REMOVE REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY LH

Click here
REMOVE REAR DOOR GLASS RUN LH

Click here
REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Click here
REMOVE REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH

Click here
REMOVE REAR DOOR REAR WINDOW FRAME LH

Click here
REMOVE REAR DOOR BELT MOULDING SUB-ASSEMBLY LH

Click here
REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH

Click here
REMOVE REAR DOOR NO. 3 GLASS RUN LH

Click here
REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH

Click here
REMOVE REAR DOOR LOCK ASSEMBLY LH
1. "TORX" screw
  
  Connector
  
  Disconnect the connector.
2. Using a T30 "TORX" socket wrench, remove the 3 TORX screws.
3. *1 Release plate
  
  Remove in this Direction
  
  Remove the 2 bolts.
4. Remove the release plate of the rear door outside handle frame sub-assembly LH in the direction indicated by the arrow shown in the illustration to remove the rear door lock assembly LH.
  
  Note
  
  Do not damage the vehicle body with the rear door lock assembly LH.
  
  Tech Tips
  
  Remove the rear door lock assembly LH while supporting it with one hand.
5. When reusing rear door lock assembly LH:
  1. Remove the door lock wire harness seal from the rear door lock assembly LH.
REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY LH
1. Open in this Direction
  
  Protective Tape
  
  Using a thin-bladed screwdriver, detach the claw and open the rear door lock cover sub-assembly LH as shown in the illustration.
2. Detach the claw and remove the rear door lock cover sub-assembly LH.
REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
1. Remove in this Direction
  
  As shown in the illustration, detach the clamp and remove the rear door lock remote control cable assembly LH.
REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
1. Remove in this Direction
  
  As shown in the illustration, detach the clamp and remove the rear door inside locking cable assembly LH.

	"TORX" screw
	Connector

*1	Release plate
	Remove in this Direction

	Open in this Direction
	Protective Tape