FRONT DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front door lock assembly removal/installation are shown below.

Replacement Part Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Removal and installation of battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize Rear Door Sunshade System Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


  • Outer rear view mirror assembly with cover LH (Including removal and installation)

  • Outer rear view mirror assembly with cover RH (Including removal and installation)

 Side television camera view adjustment Panoramic view monitor system

Click here


  • Power window regulator motor assembly LH

  • Power window regulator motor assembly RH

  • Front door window regulator assembly LH

  • Front door window regulator assembly RH

  • Front door glass sub-assembly LH

  • Front door glass sub-assembly RH

  • Front door glass run LH

  • Front door glass run RH

  • Front door front glass run LH

  • Front door front glass run RH

  • Front Door No. 2 glass run LH

  • Front Door No. 2 glass run RH

 Initialize power window control system

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When removing the front door glass sub-assembly LH, move the front door glass sub-assembly LH to the lowest position before disconnecting the battery negative (-) terminal.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B006BC1

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative(-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT DOOR TRIM UPPER COVER LH

    Click here

  5. REMOVE FRONT DOOR ARMREST COVER LH

    Click here

  6. REMOVE FRONT DOOR NO. 2 ARMREST COVER LH

    Click here

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  8. REMOVE FRONT DOOR TRIM COVER LH

    Click here

  9. REMOVE UPPER DOOR FRAME GARNISH LH

    Click here

  10. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP LH

    Click here

  11. REMOVE FRONT DOOR VENT SEAL LH

    Click here

  12. REMOVE FRONT DOOR PANEL PROTECTOR LH

    Click here

  13. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  14. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    Click here

  15. REMOVE OUTER MIRROR INSTALL HOLE COVER LH

    Click here

  16. REMOVE FRONT MULTIPLEX NETWORK DOOR ECU LH

    Click here

  17. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    Click here

  18. REMOVE DOOR SIDE AIRBAG SENSOR LH

    Click here

  19. REMOVE FRONT DOOR ARMREST SET BRACKET LH

    Click here

  20. REMOVE FRONT DOOR NO. 3 WEATHERSTRIP LH

    Click here

  21. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP LH

    Click here

  22. REMOVE FRONT DOOR BELT MOULDING LH

    Click here

  23. REMOVE FRONT DOOR REAR BELT MOULDING END COVER LH

    Click here

  24. REMOVE FRONT DOOR WINDOW FRAME MOULDING LH(CENTER PILLAR SIDE)

    Click here

  25. REMOVE FRONT PILLAR UPPER COVER SUB-ASSEMBLY LH

    Click here

  26. REMOVE FRONT DOOR GLASS RUN LH

    Click here

  27. REMOVE FRONT DOOR FRONT GLASS RUN LH

    Click here

  28. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  29. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

    Click here

  30. REMOVE FRONT DOOR NO. 2 GLASS RUN LH

    Click here

  31. REMOVE FRONT DOOR REAR WINDOW FRAME LH

    Click here

  32. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING LH

    Click here

  33. REMOVE FRONT DOOR FRONT WINDOW FRAME MOULDING LH

    Click here

  34. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

    Click here

  35. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH (for Driver Side)

    Click here

  36. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)

    Click here

  37. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH


    1. B006C43C01
      B006AHR "TORX" screw
      B006EC9 Connector

      Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the 3 TORX screws.

    3. B006CLFC01
      B006DHE Remove in this Direction

      Remove the 2 bolts and front door lock with motor assembly LH in the direction indicated by the arrow shown in the illustration.

      Note

      Do not damage the vehicle body with front door lock with motor assembly LH.

      Tech Tips

      Remove the front door lock with motor assembly LH while supporting it with one hand.

    4. When reusing front door lock with motor assembly LH:


      1. B006E4X

        Remove the door lock wire harness seal from the front door lock with motor assembly LH.

  38. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH


    1. B006BQJC01
      B006DHE Remove in this Direction
      B006GBM Protective Tape

      Using a thin-bladed screwdriver, detach the claw and open the front door lock cover sub-assembly LH.

    2. B006BAK

      Detach the claw and remove the front door lock cover sub-assembly LH.

  39. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B006FPSC01
      B006DHE Remove in this Direction

      As shown in the illustration, detach the clamp and remove the front door lock remote control cable assembly LH.

  40. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B006AEYC01
      B006DHE Remove in this Direction

      As shown in the illustration, detach the clamp and remove the front door inside locking cable assembly LH.