ENTRY AND START SYSTEM(for Entry Function) Front Passenger Side Door Entry Lock Function does not Operate

DESCRIPTION

If the entry lock function does not operate for the front passenger door only, but the entry unlock function operates, the request code is being transmitted properly from the for passenger door. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door)).

WIRING DIAGRAM

Figure 1. for LHD

B005NIXE11

Figure 2. for RHD

B005NIXE19

CAUTION / NOTICE / HINT

Note


  • The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

    Click here

  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly), refer to Precaution.

    Click here

  • After repair, confirm that no DTCs are output.

PROCEDURE


  1. CHECK POWER DOOR LOCK CONTROL SYSTEM


    1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

      Click here

      OK
      Door locks operate normally.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)


    1. Turn the engine switch off.

    2. Open and close the front passenger door.

    3. Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the front passenger door.

    4. Read the Data List according to the display on the GTS.

    5. B005OFOC01
      *A for RHD
      *B for LHD
      *a Lock Sensor

      Touch the lock sensor of the front door outside handle assembly (for front passenger door).

      Tech Tips


      • If the door does not lock even when touching the lock sensor, touch it with your palm.

      • When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).


      Body Electrical > Entry&Start > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      P-Door Trigger Switch Front passenger door touch sensor (lock sensor) ON or OFF

      ON: Front passenger door touch sensor (lock sensor) touched

      OFF: Front passenger door touch sensor (lock sensor) not touched

      • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

      • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.

      Body Electrical > Entry&Start > Data List
      Tester Display
      P-Door Trigger Switch

      Tech Tips

      When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*


      • *: w/o Double Locking System

      OK
      The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))


    1. Disconnect the R1*1 or S5*2 certification ECU (smart key ECU assembly) connector.


      • *1: for LHD

      • *2: for RHD

    2. Disconnect the M11*1 or N11*2 front door outside handle assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      R1-15 (CLG2) - M11-4 (ANT1) Always Below 1 Ω
      R1-14 (CG2B) - M11-5 (ANT2) Always Below 1 Ω
      R1-15 (CLG2) or M11-4 (ANT1) - Body ground Always 10 kΩ or higher
      R1-14 (CG2B) or M11-5 (ANT2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      S5-15 (CLG2) - N11-4 (ANT1) Always Below 1 Ω
      S5-14 (CG2B) - N11-5 (ANT2) Always Below 1 Ω
      S5-15 (CLG2) or N11-4 (ANT1) - Body ground Always 10 kΩ or higher
      S5-14 (CG2B) or N11-5 (ANT2) - Body ground Always 10 kΩ or higher

    4. Reconnect the M11*1 or N11*2 front door outside handle assembly (for front passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    5. Reconnect the R1*1 or S5*2 certification ECU (smart key ECU assembly) connector.


      • *1: for LHD

      • *2: for RHD

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (INPUT TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

    B005OAJC14
    *A for LHD *B for RHD
    *a

    Component with harness connected

    (Certification ECU (Smart Key ECU Assembly))

    		 *b Waveform 1
    *c Lock sensor not touched *d Lock sensor touched

    1. Using an oscilloscope, check the waveform.

      OK
      for LHD
      Tester Connection Condition Tool Setting Specified Condition
      R1-15 (CLG2) - J41-18 (E)

      Procedure:


      1. Engine switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. All doors closed

      4. All doors locked through wireless operation

        (electrical key transmitter sub-assembly brought outside detection area*)

      5. Front passenger door lock sensor touched

      		 5 V/DIV., 40 ms/DIV.

      Pulse generation

      (See waveform 1)
      for RHD
      Tester Connection Condition Tool Setting Specified Condition
      S5-15 (CLG2) - J41-18 (E)

      Procedure:


      1. Engine switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. All doors closed

      4. All doors locked through wireless operation

        (electrical key transmitter sub-assembly brought outside detection area*)

      5. Front passenger door lock sensor touched

      		 5 V/DIV., 40 ms/DIV.

      Pulse generation

      (See waveform 1)

      *: For details about the entry function detection area, refer to Operation Check.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) Click here