SIDE AIRBAG SENSOR(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic View Monitor System

Click here

Initialize Rear Door Sunshade System Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    Click here

    B006BC1

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE FRONT DOOR UPPER TRIM COVER LH

    Click here

  5. REMOVE FRONT DOOR ARMREST COVER LH

    Click here

  6. REMOVE FRONT DOOR NO. 2 ARMREST COVER LH

    Click here

  7. REMOVE COURTESY LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  9. REMOVE FRONT DOOR SERVICE HOLE COVER LH

    Click here

  10. REMOVE DOOR SIDE AIRBAG SENSOR LH


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • B006BY6

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      • B006AIG

        If this procedure is performed without disconnecting the negative (-) battery terminal, the airbag may deploy even if an impact is applied only to the door side airbag sensor LH. Therefore, make sure that the negative (-) battery terminal is disconnected before performing this procedure.

    3. B006D6LC01
      B006DHE Pull Out

      Remove the nut.

      Note

      Do not reuse the nut.

    4. Detach the claw and pull out the door side airbag sensor LH.

      Note

      If the door side airbag sensor LH has been dropped, replace it with a new one.

    5. Disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

        B006ENWC06
        *a Housing Lock *b CPA
        *c CPA Upper Part *d Connector Lock is Released

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B006EG6C21
        *a CPA *b Housing
        *c Correct *d Incorrect