REPAIR INSTRUCTION INITIALIZATION


  1. Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
    Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

    for 8GR-FKS: Click here

    for V35A-FTS: Click here

    Memorize steering angle neutral point LKA/LDA system

    Click here

    Parking support brake system*
    Pre-collision system
    Adaptive high beam system

      Lighting system (EXT)

    • Cornering lights

    Variable gear ratio steering system

    Click here

    Parking assist monitor system

    Click here

    Panoramic view monitor system

    Click here

    Initialize rear door sunshade system Rear door sunshade system

    Click here

    Initialize power trunk lid system Power trunk lid system

    Click here

    *: When performing learning using the GTS.

    Click here

    PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

    Note

    After the engine switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the engine switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) battery Terminal
    System Name See Procedure
    Vehicle enrolled in telematics system (for G-BOOK) 6 minutes
    Vehicle not enrolled in telematics system (for G-BOOK) 1 minute
  2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

    Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed Link
    ECM

      for 8GR-FKS:

    • Vehicle Identification Number (VIN) registration

    DTC P0630 is output

    Click here


      for V35A-FTS, w/ Canister Pump Module:

    • Vehicle Identification Number (VIN) registration

    DTC P063051 is output

    Click here


      for V35A-FTS, w/o Canister Pump Module:

    • The Vehicle Identification Number (VIN) or frame number registration

    Click here


      for V35A-FTS:

    • Heavy Knock History


      • Save history

      • Write history

    -

    w/ Canister Pump Module: Click here

    w/o Canister Pump Module: Click here


      for V35A-FTS, w/o Canister Pump Module:

    • GPF Deposition Values*1


      • GPF deposition values save

      • GPF deposition values write


    • MIL comes on

    • Deterioration of fuel efficiency

    Click here

    Perform code registration Engine start See Service Bulletin for the registration method.

      for AGA0E:

    • If possible, read the transmission compensation code from the previous ECM


      • Transfer transmission compensation code (step 2)*2

      • Perform road test to allow ECM to learn


    • Large shift shock

    • Engine overruns

    for 8GR-FKS, Initialization: Click here

    for 8GR-FKS, Registration: Click here

    for V35A-FTS, Initialization: Click here

    for V35A-FTS, Registration: Click here


      for AGA0E:

    • If impossible, the transmission compensation code cannot be read from the previous ECM


      • Set transmission compensation code (step 1)*3

      • Perform road test to allow ECM to learn


      for AGA0F:

    • If possible, read the transmission compensation code from the previous ECM


      • Transfer transmission compensation code (step 2)*2

      • Perform road test to allow ECM to learn


    • Large shift shock

    • Engine overruns

    for Initialization: Click here

    for Registration: Click here


      for AGA0F:

    • If impossible, the transmission compensation code cannot be read from the previous ECM


      • Set transmission compensation code (step 1)*3

      • Perform road test to allow ECM to learn


      for 8GR-FKS:

    • Throttle body with motor assembly

    • Cleaning the deposits from the throttle body with motor assembly

    • Cylinder head sub-assembly

    • Camshaft (for intake or exhaust camshaft)

    • Camshaft timing gear assembly

    • Camshaft timing exhaust gear assembly

    • Piston or piston ring

    • Mass air flow meter sub-assembly

    • Fuel injector assembly (for port injection)

    • Fuel injector assembly (for direct injection)

    • Fuel pump (for low pressure side)

    • Fuel pump assembly (for high pressure side)

    • Fuel pressure sensor (for low pressure side)

    • Fuel pressure sensor (for high pressure side)

    • Air fuel ratio sensor (sensor 1)

    • Air fuel ratio sensor (sensor 2)

    • Engine coolant temperature sensor

    • Spark plug

    • Ignition coil assembly

    • Air leaks from intake system

    • Gas leaks from exhaust system

    • Knock control sensor

    Inspection after repair
    • Poor idle, etc.

    • Engine start function, etc.

    Click here


      for V35A-FTS:

    • Throttle body with motor assembly

    • Cleaning the deposits from the throttle body with motor assembly

    • Cam timing control motor with EDU assembly (Including removal and installation)

    • Camshaft timing intake gear assembly (Including removal and installation)

    • Cylinder head sub-assembly

    • Camshaft (for intake or exhaust camshaft)

    • Camshaft timing exhaust gear assembly

    • Piston

    • Mass air flow meter sub-assembly

    • Port fuel injector assembly

    • Direct fuel injector assembly

    • Fuel pump (for low pressure side)

    • Fuel pump assembly (for high pressure side)

    • No. 2 fuel pressure sensor (for low pressure side)

    • Fuel pressure sensor (for high pressure side)

    • Air fuel ratio sensor (sensor 1)

    • Air fuel ratio sensor (sensor 2)

    • Engine coolant temperature sensor (for inlet side)

    • Engine coolant temperature sensor (for cylinder head side)

    • Engine coolant temperature sensor (for outlet side)

    • Spark plug

    • Ignition coil assembly

    • Air leaks from intake system

    • Gas leaks from exhaust system

    • Knock control sensor

    • Turbocharger sub-assembly

    Inspection after repair
    • Poor idle, etc.

    • Engine start function, etc.

    w/ Canister Pump Module: Click here

    w/o Canister Pump Module: Click here

    Engine assembly

      for 8GR-FKS:

    • Inspection after repair


    • Poor idle, etc.

    • Engine start function, etc.

    Click here


      for V35A-FTS:

    • Inspection after repair


    • Poor idle, etc.

    • Engine start function, etc.

    w/ Canister Pump Module: Click here

    w/o Canister Pump Module: Click here


      for AGA0E:

    • Reset memory

    • Perform road test to allow ECM to learn


    • Large shift shock

    • Engine overruns

    for 8GR-FKS: Click here

    for V35A-FTS: Click here


      for AGA0F:

    • Reset memory

    • Perform road test to allow ECM to learn


    • Large shift shock

    • Engine overruns

    Click here


      for V35A-FTS:

    • Piston ring

    Inspection after repair
    • Poor idle, etc.

    • Engine start function, etc.

    w/ Canister Pump Module: Click here

    w/o Canister Pump Module: Click here

    Heavy Knock History


    • Initializes the stored history data

    -

      for V35A-FTS, w/o Canister Pump Module:

    • Front exhaust pipe assembly*1

    GPF deposition value clear
    • MIL comes on

    • Deterioration of fuel efficiency

    Click here


    • Forward recognition camera

    • Windshield glass (Including removal and installation)

    Adjust forward recognition camera
    • Dynamic radar cruise control system

    • Front camera system

    • LKA/LDA system

    • Road sign assist system

    • Pre-collision system

    • Automatic high beam system

    • Adaptive high beam system

    Click here

    Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly
    • Dynamic radar cruise control system

    • Front camera system

    • LKA/LDA system

    • Pre-collision system

    Click here

    Engine stop and start ECU
    • Upload the number of starter operations

    • Reset air conditioning information

    • Learning air conditioning information

    • Clear the zero point calibration data

    • Deceleration sensor zero point calibration

    Stop and start system

    for 8GR-FKS: Click here

    for V35A-FTS: Click here


      w/ Stop and Start System:

    • Air conditioning amplifier assembly


    • Reset air conditioning information

    • Learning air conditioning information


      w/ Stop and Start System:

    • Starter assembly

    Note

    When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.

    Clear number of starter operations

      w/ Stop and Start System:

    • Airbag ECU assembly


    • Clear the zero point calibration data

    • Deceleration sensor zero point calibration


      w/ Stop and Start System:

    • Battery


    • Integrated current value initialization

    • Switch battery type


      for AGA0E:

    • Automatic transmission assembly


    • Set transmission compensation code (step 1)*4

    • Perform road test to allow ECM to learn


    • Large shift shock

    • Engine overruns

    for 8GR-FKS, Initialization: Click here

    for 8GR-FKS, Registration: Click here

    for V35A-FTS:, Initialization: Click here

    for V35A-FTS:, Registration: Click here


      for AGA0E:

    • Transmission valve body assembly

    • Solenoid (SL1, SL2, SL3, SL4, SL5 and SL6) valves

    Perform road test to allow ECM to learn

      for AGA0E:

    • Automatic transmission fluid

    ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

    for 8GR-FKS: Click here

    for V35A-FTS: Click here


      for AGA0F:

    • Automatic transmission assembly with transfer


    • Set transmission compensation code (step 1)*4

    • Perform road test to allow ECM to learn


    • Large shift shock

    • Engine overruns

    for Initialization: Click here

    for Registration: Click here


      for AGA0F:

    • Transmission valve body assembly

    • Solenoid (SL1, SL2, SL3, SL4, SL5 and SL6) valves

    Perform road test to allow ECM to learn

      for AGA0F:

    • Automatic transmission fluid

    ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

    Click here


    • Suspension control ECU

    • Height control sensor

    Vehicle height offset calibration
    • Vehicle height sensor data may be affected due to installation position, or vehicle height recognition may be erroneous

    • Air suspension control

    Click here

    Absorber Control ECU Registration of Vehicle Identification Information
    • Interrupts damping force control

    • DTCs are stored

    Click here


    • Front active stabilizer control ECU assembly

    • Front active stabilizer control actuator assembly

    • Rear active stabilizer control ECU assembly

    • Rear active stabilizer control actuator assembly

    Motor rotation angle sensor calibration Active stabilizer is not operating

    Click here


    • Tire pressure warning ECU and receiver

    • Tire pressure warning valve and transmitter


    • Register transmitter ID

    • Initialize tire pressure warning system

    • Perform tire position identification


    • When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

    • Tire pressure warning function

    for Initialization: Click here

    for Registration: Click here


      Electronically Controlled Brake System (w/ Vacuum Brake Booster):

    • Brake actuator assembly (Skid control ECU) (Including removal and installation)


    • Bleed air

    • Perform acceleration sensor (yaw rate sensor) zero point calibration and store system information


    • DTCs are stored

    • ABS warning light illuminates

    • Brake system warning light (red indicator) illuminates

    • Slip indicator light illuminates

    • VSC disabled or malfunctions

    Click here


      Electronically Controlled Brake System (w/o Vacuum Brake Booster):

    • Brake actuator assembly (Including removal and installation)


    • Bleed air

    • Clear stored linear solenoid valve calibration data

    • Perform initialization and calibration of the linear solenoid valve


    • DTCs are output

    • ABS warning light illuminates

    • Brake warning light/yellow (minor malfunction) illuminates

    • Slip indicator light illuminates

    • VSC disabled or malfunctions

    Click here


      Electronically Controlled Brake System (w/o Vacuum Brake Booster):

    • Skid control ECU assembly


    • Clear stored linear solenoid valve calibration data

    • Perform initialization and calibration of the linear solenoid valve

    • Clear zero point calibration data

    • Perform yaw rate sensor zero point calibration


    • DTCs are output

    • ABS warning light illuminates

    • Brake warning light/yellow (minor malfunction) illuminates

    • Slip indicator light illuminates

    • VSC disabled or malfunctions

    for Initialization: Click here

    for Calibration: Click here


      Electronically Controlled Brake System (w/o Vacuum Brake Booster):

    • Brake pedal stroke sensor assembly(Including removal and installation)

    • Brake pedal support assembly (Including removal and installation)


    • Clear stored linear solenoid valve calibration data

    • Perform initialization and calibration of the linear solenoid valve


    • DTCs are output

    • ABS warning light illuminates

    • Brake warning light/yellow (minor malfunction) illuminates

    • Slip indicator light illuminates

    • VSC disabled or malfunctions

    Click here

    Yaw rate sensor

      Electronically Controlled Brake System (w/o Vacuum Brake Booster):

    • Clear stored linear solenoid valve calibration data

    • Perform initialization and calibration of the linear solenoid valve

    • Clear zero point calibration data

    • Perform yaw rate sensor zero point calibration


    • DTCs are output

    • ABS warning light illuminates

    • Brake warning light/yellow (minor malfunction) illuminates

    • Slip indicator light illuminates

    • VSC disabled or malfunctions

    for Initialization: Click here

    for Calibration: Click here


      Electronically Controlled Brake System (w/ Vacuum Brake Booster):

    • Clear zero point calibration data and system information

    • Perform acceleration sensor (yaw rate sensor) and zero point calibration and store system information


    • DTCs are stored

    • ABS warning light illuminates

    • Brake system warning light (red indicator) illuminates

    • Slip indicator light illuminates

    • VSC disabled or malfunctions

    Click here

    Electric parking brake ECU
    • Reset memory

    • Acquire tension sensor zero point

    Electric parking brake system

    Click here

    Parking brake actuator assembly with bracket (Including removal and installation)
    • Reset memory

    • Acquire tension sensor zero point

    • Parking brake bedding


    • Rear disc (Including removal and installation)

    • Parking brake shoe (Including removal and installation)

    Parking brake bedding
    Rack and pinion power steering gear assembly
    • Torque sensor zero point calibration

    • Assist map writing


    • DTCs are output

    • EPS warning light illuminated

    Click here


    • VGRS ECU (front steering control ECU)

    • Steering actuator assembly

    • Parts between the steering wheel and tires have been removed/installed, replaced or adjusted

    Perform actuator angle neutral point calibration and initialization
    • Variable gear ratio steering system

    • Steering wheel off-center

    • DTCs are output

    Click here

    DRS ECU (rear steering control ECU) Perform neutral position memorization and motor rotation angle sensor calibration
    • Dynamic rear steering system

    • Steering wheel off-center

    • DTCs are output

    Click here

    Rear steering link assembly or rear suspension have been removed/installed, replaced, or adjusted
    • Perform actuator calibration value initialization

    • Perform neutral position memorization and motor rotation angle sensor calibration

    Steering wheel off-center

      for G-BOOK:

    • Navigation ECU

    Vehicle contract setting G-BOOK function

    Click here

    Download necessary data

    Click here


      for G-BOOK:

    • Radio receiver assembly

    Download necessary data G-BOOK function

    Click here


      for ERA-GLONASS:

    • Mobile phone battery

    Reset mobilephone battery condition Emergency call service

    Click here

    Telematics transceiver assembly

      for ERA-GLONASS:

    • Register vehicle information

    Emergency call service

    Click here


      for G-BOOK:

    • Vehicle contract setting

    G-BOOK function

    Click here


      w/ Parking Support Brake System

    • Clearance warning ECU assembly


    • Ultrasonic sensor detection angle

    • Steering angle neutral point

    • Registration of bumper type

    • Ultrasonic sensor detection angle registration


    • Parking support brake system

    • Parking support alert system

    Click here


      w/ Parking Support Brake System

    • Ultrasonic sensor (Including removal and installation)


    • Ultrasonic sensor detection angle

    • Ultrasonic sensor detection angle registration


      w/o Parking Support Brake System

    • Clearance warning ECU assembly

    Registration of bumper type Parking support alert system

    Click here


      w/o Parking Support Brake System

    • Ultrasonic sensor (front left sensor, front left center sensor, front right center sensor, front right sensor)

    Initialization of ultrasonic sensors (front left sensor, front left center sensor, front right center sensor, front right sensor) Parking support alert system

      w/o Parking Support Brake System

    • Ultrasonic sensor (rear left sensor, rear left center sensor, rear right center sensor, rear right sensor)

    Initialization of ultrasonic sensors (rear left sensor, rear left center sensor, rear right center sensor, rear right sensor) Parking support alert system
    Rear bumper assembly (Including removal and installation)
    • Ultrasonic sensor detection angle

    • Ultrasonic sensor detection angle registration

    Parking support brake system

    Click here

    Front bumper assembly (Including removal and installation)
    • Ultrasonic sensor detection angle

    • Ultrasonic sensor detection angle registration

    Parking support brake system

    Click here

    Front television camera view adjustment Panoramic view monitor system

    Click here

    Suspension, tires, etc.
    • Ultrasonic sensor detection angle

    • Ultrasonic sensor detection angle registration

    Parking support brake system

    Click here


    • Parking assist ECU initialization

    • Adjust steering angle

    • Rear television camera view adjustment (for Rear camera detection system)

    Panoramic view monitor system

    Click here

    Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system

    Click here

    Steering sensor (Including removal and installation) Steering angle neutral point Parking support brake system

    Click here

    Parking assist monitor system

    Click here

    Panoramic view monitor system

    Click here

    Steering angle setting Parking assist monitor system

    Click here

    Panoramic view monitor system

    Click here

    Parking assist ECU
    • Parking assist ECU initialization

    • Adjust steering angle

    Panoramic view monitor system

    Click here


    • Front television camera assembly (Including removal and installation)

    • Radiator grille (Including removal and installation)

    Front television camera view adjustment

    • Side television camera assembly LH (Including removal and installation)

    • Side television camera assembly RH (Including removal and installation)

    • Outer rear view mirror assembly with cover LH (Including removal and installation)

    • Outer rear view mirror assembly with cover RH (Including removal and installation)

    Side television camera view adjustment

    • Front television camera assembly, front bumper assembly or radiator grille

    • Rear television camera assembly

    • Side television camera assembly LH or outer rear view mirror assembly LH

    • Side television camera assembly RH or outer rear view mirror assembly RH


    • Television camera view adjustment

    • Rear television camera view adjustment (for Rear camera detection system)

    Rear television camera assembly (Including removal and installation)
    • Rear television camera view adjustment

    • Rear television camera view adjustment (for Rear camera detection system)


    • Parking support alert system

    • Parking support brake system

    • Panoramic view monitor system

    Click here


    • Parking assist monitor system initialization

    • Rear television camera assembly optical axis (Back camera position setting)

    Parking assist monitor system

    Click here

    Blind spot monitor sensor Blind spot monitor beam axis confirmation
    • DTCs are output

    • Parking support alert system

    • Parking support brake system

    • Blind spot monitor system

    Click here

    Inner rear view mirror assembly Registration Garage door does not operative

    Click here


    • Certification ECU (smart key ECU assembly)

    • Steering lock ECU (steering lock actuator or upper bracket assembly)

    • Electrical key transmitter sub-assembly

    • ID code box (immobiliser code ECU)

    • Main body ECU (multiplex network body ECU)

    Perform code registration
    • Wireless door lock control system

    • Entry and start system

    • Engine start

    See Service Bulletin for the registration method.

    • Occupant detection ECU (Including removal and installation)

    • Front seat assembly RH (Only for removal and installation)

    Zero point calibration (Occupant classification system)
    • Occupant classification system

    • Passenger airbag ON/OFF indicator

    • Airbag system (Front passenger side)

    • Seat belt warning system (Front passenger)

    Click here


    • Position control ECU assembly (Including removal and installation)

    • No. 2 position control ECU assembly (Including removal and installation)

    • Front seat headrest assembly (Including removal and installation)

    • Power seat switch LH (Including removal and installation)

    • Power seat switch RH (Including removal and installation)

    • Front seatback frame sub-assembly LH (Including removal and installation)

    • Front seatback frame sub-assembly RH (Including removal and installation)

    • Front seat adjuster assembly LH (Including removal and installation)

    • Front seat adjuster assembly RH (Including removal and installation)

    • Front seat headrest insert sub-assembly LH (Including removal and installation)

    • Front seat headrest insert sub-assembly RH (Including removal and installation)

    Initialize position control ECU Front power seat control system

    Click here


    • Position control ECU assembly LH (Including removal and installation)

    • Position control ECU assembly RH (Including removal and installation)

    • Rear seat headrest assembly RH (Including removal and installation)

    • Rear seat headrest assembly LH (Including removal and installation)

    • Rear No. 1 seat adjuster assembly (Including removal and installation)

    • Rear No. 2 seat adjuster assembly (Including removal and installation)

    Initialize position control ECU Rear power seat control system

    Click here


      for LHD:

    • No. 1 seat reclining adjuster assembly RH (Including removal and installation)


      for RHD:

    • No. 1 seat reclining adjuster assembly LH (Including removal and installation)


    • No. 1 blower damper servo sub-assembly

    • No. 1 air conditioning radiator damper servo sub-assembly

    • No. 2 air conditioning radiator damper servo sub-assembly

    • No. 3 air conditioning radiator damper servo sub-assembly

    • No. 4 air conditioning radiator damper servo sub-assembly

    • No. 5 air conditioning radiator damper servo sub-assembly

    • No. 6 air conditioning radiator damper servo sub-assembly

    • No. 1 rear cooling Unit damper servo sub-assembly

    Initialization servo motor DTCs are output

    Click here


    • Rear multiplex network door ECU LH

    • Rear multiplex network door ECU RH

    • Rear multiplex network door ECU LH or rear multiplex network door ECU RH is the connectors are disconnected

    Initialize rear door sunshade system The rear door sunshade system does not operate

    Click here


    • Power window regulator motor assembly LH

    • Power window regulator motor assembly RH

    • Front door window regulator assembly LH

    • Front door window regulator assembly RH

    • Rear door window regulator assembly LH

    • Rear door window regulator assembly RH

    • Front door glass sub-assembly LH

    • Front door glass sub-assembly RH

    • Rear door glass sub-assembly LH

    • Rear door glass sub-assembly RH

    • Front door glass run LH

    • Front door glass run RH

    • Front door front glass run LH

    • Front door front glass run RH

    • Front Door No. 2 glass run LH

    • Front Door No. 2 glass run RH

    • Rear door glass run LH

    • Rear door glass run RH

    • Rear door No. 3 glass run LH

    • Rear door No. 3 glass run RH

    Initialize power window control system
    • Auto up and down function

    • Jam protection function

    • Catch protection function

    • Remote control function

    • Key-linked function

    • Wireless transmitter-linked function

    • Key-off operation function

    • Window open warning function

    Click here

    Sliding roof glass sub-assembly (Including removal and installation) Initialize sliding roof system
    • Auto function

    • Jam protection function

    • Key-off operation

    • Wireless transmitter-linked operation

    • Key-linked function

    • Open warning function may not operate

    • Sliding roof may become misaligned

    Click here

    Initialize panoramic moon roof system
    • Auto operation function

    • Jam protection function

    • Key-off operation function

    • Key-linked function

    • Wireless transmitter-linked function

    • Sliding roof open warning function may not operate

    • Sliding roof may move in reverse or become misaligned

    Click here

    Sliding roof drive gear sub-assembly Initialize sliding roof system
    • Auto function

    • Jam protection function

    • Key-off operation

    • Wireless transmitter-linked operation

    • Key-linked function

    • Open warning function may not operate

    • Sliding roof may become misaligned

    Click here

    Initialize panoramic moon roof system
    • Auto operation function

    • Jam protection function

    • Key-off operation function

    • Key-linked function

    • Wireless transmitter-linked function

    • Sliding roof open warning function may not operate

    • sliding roof may move in reverse or become misaligned

    Click here

    Sliding roof drive gear assembly (Including removal and installation) Initialize roof sunshade system
    • Auto open and close function

    • Jam protection function may not operate

    • Roof sunshade may move in reverse or become misaligned

    Click here

    Sliding roof housing assembly (Including removal and installation) Initialize panoramic moon roof system
    • Auto operation function

    • Jam protection function

    • Key-off operation function

    • Key-linked function

    • Wireless transmitter-linked function

    • Sliding roof open warning function may not operate

    • Sliding roof may move in reverse or become misaligned

    Click here


    • Sliding roof housing sub-assembly (Including removal and installation)

    • Sliding roof housing assembly (Including removal and installation)

    Initialize roof sunshade system
    • Auto open and close function

    • Jam protection function may not operate

    • Roof sunshade may move in reverse or become misaligned

    Click here

    Slide roof rail sub-assembly (Including removal and installation) Initialize panoramic moon roof system
    • Auto operation function

    • Jam protection function

    • Key-off operation function

    • Key-linked function

    • Wireless transmitter-linked function

    • Sliding roof open warning function may not operate

    • Sliding roof may move in reverse or become misaligned

    Click here

    Kick door control sensor Reset connection history There are cases where the connection history display differs from the vehicle condition

    Click here

    The luggage closer motor assembly Reset connection history There are cases where the connection history display differs from the vehicle condition

    Click here

    Initialize luggage closer motor assembly The power trunk lid does not operate

    Click here

    The luggage closer motor assembly connector is disconnected Initialize luggage closer motor assembly The power trunk lid does not operate

    Click here


      w/ Power Trunk Lid System:

    • When the luggage compartment door is opened using a mechanical key

    Headlight ECU sub-assembly LH

      w/ Adaptive Variable Suspension System:

    • Synchronize the vehicle information

    Automatic headlight beam level control system

    Click here


      w/o Adaptive Variable Suspension System:

    • Synchronize the vehicle information

    • Perform headlight ECU sub-assembly LH initialization


      w/o Adaptive Variable Suspension System:

    • Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed.

    Perform headlight ECU sub-assembly LH initialization

    *1: w/ Gasoline Particulate Filter

    *2: Read the transmission compensation code from the previous ECM, then transfer it to the new ECM.

    *3: Set the transmission compensation code of the current automatic transmission.

    *4: Set the transmission compensation code for the new automatic transmission.