FRONT SEAT INNER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • B006B4P

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

PROCEDURE


  1. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)


    1. Install the front seat belt anchor plate.

    2. w/ Easy Access Buckle:


      1. B006B06C01
        B006DHE Install in this Direction

        Pass the buckle of the front seat inner belt assembly LH through the hole of the separate type front seat cushion cover LH.

      2. B006FSOC03
        *a Stud Bolt
        *b Protruding Part

        Temporarily install the front seat inner belt assembly LH to the stud bolt.

      3. Install the 2 nuts.

        Torque:
        Nut A
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
        Nut B
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note

        Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part.

    3. w/o Easy Access Buckle:


      1. B006FDPC04
        *a Protruding Part

        Install the front seat inner belt assembly LH with the nut.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

        Note

        Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part.

    4. Attach the claw and install the connector.

      B006BPPC03
      *A for 2WD *B for AWD
      *C w/o Easy Access Buckle *D w/ Easy Access Buckle
      B006DHE Install in this Direction - -

    5. Attach the wire harness clamp.

    6. Connect the 2 connectors.

  2. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)


    1. w/ Easy Access Buckle:


      1. B006AYDC01
        B006DHE Install in this Direction

        Pass the buckle of the front seat inner belt assembly RH through the hole of the separate type front seat cushion cover RH.

      2. B006ER5C03
        *a Stud Bolt
        *b Protruding Part

        Temporarily install the front seat inner belt assembly RH to the stud bolt.

      3. Install the 2 nuts.

        Torque:
        Nut A
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
        Nut B
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note

        Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part.

    2. w/o Easy Access Buckle:


      1. B006BFXC03
        *a Protruding Part

        Install the front seat inner belt assembly RH with the nut.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

        Note

        Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part.

    3. Attach the claw and install the connector.

      B006ESOC02
      *A w/ Easy Access Buckle *B w/o Easy Access Buckle
      B006DHE Install in this Direction - -

    4. Attach the wire harness clamp.

    5. Connect the connector.

  3. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  4. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSPECT SRS WARNING LIGHT

    Click here

  6. INSPECT SEAT BELT WARNING SYSTEM

    Click here

  7. INSPECT FRONT SEAT ASSEMBLY

    Click here

  8. INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

    Click here

  9. INSPECT CLIMATE CONTROL SEAT SYSTEM (w/ Climate Control Seat System)

    Click here

  10. INSPECT SEAT VIBRATION SYSTEM (w/ Refresh Seat)

    Click here