PROCEDURE
INSPECT DRIVER SEAT BELT WARNING SYSTEM
Tech Tips
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
Turn the engine switch on (IG).
When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.
Lift up the vehicle using a swing arm type lift.
Start the engine.
When the driver seat belt is not fastened, the parking brake is released and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that seat belt warning light on the combination meter blinks at an interval of 1.2 seconds.
When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.
After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 90 seconds and then illuminates.
When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
INSPECT FRONT PASSENGER SEAT BELT WARNING SYSTEM
Tech Tips
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
Turn the engine switch on (IG).
Place a weight of 20 kg (44.0 lb) on the front passenger seat.
Note
Place the weight on the seat cushion and do not allow it to come into contact with the seatback.
Fasten the driver seat belt.
When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.
Lift the vehicle using a swing arm type lift.
Start the engine.
When the front passenger seat belt is not fastened, the parking brake is released and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that seat belt warning light on the combination meter blinks at an interval of 1.2 seconds.
When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.
After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 90 seconds and then illuminates.
When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.
INSPECT REAR SEAT BELT WARNING LIGHT
*1 | Rear Seat Belt Warning Light (Combination Meter Assembly) |
*a | LH |
*b | Center |
*c | RH |
Check the state of the rear seat belt warning light on the telltale light assembly:
Turn the engine switch off.
Open and then close either rear door.
Turn the engine switch on (IG).
Place a weight of 20 kg (44.0 lb) on the front passenger seat.*
*: for Type B
Note
Place the weight on the seat cushion and do not allow it to come into contact with the seatback.
When a rear seat belt is not fastened, check that the rear seat belt warning light on the telltale light assembly is illuminated.
After 30 seconds, check that the rear seat belt warning light on the telltale light assembly turns off.
When one of the rear seat belts is unfastened from being fastened, check that the rear seat belt warning light on the telltale light assembly illuminates.
INSPECT SEAT BELT WARNING BUZZER
Tech Tips
The seat belt warning buzzer can be customized. Make sure that this function is ON.
for Front Seat Belt Warning Buzzer:
Place a weight of 20 kg (44.0 lb) on the front passenger seat.
Note
Place the weight on the seat cushion and allow it to come into contact with the seatback.
Lift the vehicle using a swing arm type lift.
Start the engine.
When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.
After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.
Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.
After the seat belt warning buzzer in the combination meter assembly stops, turn the engine switch off and then start the engine again. Drive the vehicle at approximately 20 km/h (12 mph) or more with either the driver or front passenger seat belt not fastened and check that the buzzer sounds in the same pattern again.
After the seat belt warning buzzer in the combination meter assembly stops, fasten the driver or front passenger seat belt, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the driver or front passenger seat belt and check that the buzzer sounds in the same pattern again.
for Rear Seat Belt Warning Buzzer:
Place a weight of 20 kg (44.0 lb) on the front passenger seat.*
Note
Place the weight on the seat cushion and allow it to come into contact with the seatback.
*: for Type B
Open and close either rear door.
Lift the vehicle using a swing arm type lift.
Fasten the driver seat belt.
Start the engine.
Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the seat belt warning buzzer in the combination meter assembly sounds once.
After the seat belt warning buzzer sounds once, check that it sounds at an interval of 1.2 seconds for 6 seconds.
After the seat belt warning buzzer has been sounding for 6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 30 seconds.
Check that the seat belt warning buzzer in the combination meter assembly stops 36 seconds after it started sounding at an interval of 1.2 seconds.
After the seat belt warning buzzer in the combination meter assembly stops, turn the engine switch off, open and close either rear door and then start the engine again. Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the buzzer sounds in the same pattern again.
After the seat belt warning buzzer in the combination meter assembly stops, fasten a rear seat belt, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the rear seat belt and check that the buzzer sounds in the same pattern again.