SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P010014, P010016

DTC Code DTC Name
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open
P010016 Mass or Volume Air Flow Sensor "A" Circuit Voltage Below Threshold

DESCRIPTION

Refer to DTC P010012.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open

The mass air flow meter sub-assembly voltage is below 0.2 V for 3 seconds or more.

(1 trip detection logic: Engine speed is less than 4000 rpm)


  • Open or short in mass air flow meter sub-assembly circuit

  • Mass air flow meter sub-assembly

  • ECM

Comes on DTC stored SAE: P0102
P010016 Mass or Volume Air Flow Sensor "A" Circuit Voltage Below Threshold

The mass air flow meter sub-assembly voltage is below 0.2 V for 3 seconds or more.

(2 trip detection logic: Engine speed is 4000 rpm or more)


  • Open or short in mass air flow meter sub-assembly circuit

  • Mass air flow meter sub-assembly

  • ECM

Comes on DTC stored SAE: P0102

Tech Tips

When a DTC is output, check the Data List item "Mass Air Flow Sensor" using the GTS.

Click here

DTC No. Mass Air Flow Sensor Malfunction

P010014

P010016

0 gm/sec
  • Open in mass air flow meter sub-assembly power source circuit

  • Open or short in VG circuit

If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V for 3 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

B008HF8E21

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on [A].

  6. Start the engine.

  7. Idle the engine for 5 seconds [B].

  8. Enter the following menus: Powertrain / Engine / Trouble Codes [C].

  9. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  10. Run the engine at an engine speed of 4000 rpm or higher for 5 seconds [D].

  11. Enter the following menus: Powertrain / Engine / Trouble Codes [E].

  12. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  14. Input the DTC: P010014 or P010016.

  15. Check the DTC judgment result.

    GTS Display Description
    NORMAL
    • DTC judgment completed

    • System normal

    ABNORMAL
    • DTC judgment completed

    • System abnormal

    INCOMPLETE
    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    N/A
    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

WIRING DIAGRAM

Refer to DTC P010012.

Click here

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)


    1. B008GOLC25
      *a

      Front view of wire harness connector

      (to Mass Air Flow Meter Sub-assembly)

      Disconnect the mass air flow meter sub-assembly connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C1-3 (+B) - Body ground Engine switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG
    OK
  2. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)


    1. Disconnect the mass air flow meter sub-assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C1-5 (VG) - C20-92 (VG) Always Below 1 Ω
      C1-5 (VG) or C20-92 (VG) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG
    OK
  3. INSPECT MASS AIR FLOW METER SUB-ASSEMBLY


    1. Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter.

      Click here

    2. Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter.

      Click here

    3. Inspect the function of the mass air flow meter sub-assembly.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.


        Powertrain > Engine > Data List
        Tester Display
        Mass Air Flow Sensor
      5. Start the engine.

      6. Check that the Mass Air Flow Sensor value changes when the engine is raced.

        OK
        The reading changes.

        Tech Tips

        Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

        Click here

      Result
      Proceed to
      OK
      NG

    OK
    NG