INSTALL SLIDING ROOF HOUSING DRAIN END CAP RH (w/ Sliding Roof)
*1 | Marking |
Install a new sliding roof housing drain end cap RH.
INSTALL SLIDING ROOF HOUSING DRAIN END CAP LH (w/ Sliding Roof)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL REAR SLIDING ROOF DRAIN HOSE RH (w/ Sliding Roof)
Install the rear sliding roof drain hose RH.
INSTALL REAR SLIDING ROOF DRAIN HOSE LH (w/ Sliding Roof)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
Put the roof headlining assembly into the vehicle through the back door.
Note
Do not damage the roof headlining assembly or body interior.
Engage the 2 guides.
Engage the 2 clips and 6 fasteners.
After positioning the roof headlining assembly, push on it towards each sliding roof housing drain end cap to engage the claws.
Note
Do not damage or crease the roof headlining assembly.
Connect the No. 2 antenna cord sub-assembly connector and engage the clamps to the rear pillar RH.
Connect the rear No. 2 washer hose to the rear pillar RH.
Connect the No. 2 antenna cord sub-assembly connectors and engage each clamp to the front pillar RH.
Connect the rear No. 2 washer hose to the front pillar RH.
Note
After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.
Connect the 4 No. 1 roof wire connectors to the instrument panel junction block.
Connect the No. 1 roof wire and engage each clamp to the front pillar LH.
w/ EC Mirror:
Connect the connector.
w/ Rain Sensor:
Connect the connector.
INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
Put the roof headlining assembly into the vehicle through the back door.
Note
Do not damage the roof headlining assembly or body interior.
Engage the 2 guides.
Engage the 2 clips and 28 fasteners.
After positioning the roof headlining assembly, push on it towards each sliding roof housing drain end cap to engage the claws.
Note
Do not damage or crease the roof headlining assembly.
Connect the No. 2 antenna cord sub-assembly connector and engage the clamps to the rear pillar RH.
Connect the rear No. 2 washer hose to the rear pillar RH.
Connect the No. 2 antenna cord sub-assembly connectors and engage each clamp to the front pillar RH.
Connect the rear No. 2 washer hose to the front pillar RH.
Note
After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.
Connect the 4 No. 1 roof wire connectors to the instrument panel junction block.
Connect the No. 1 roof wire and engage each clamp to the front pillar LH.
w/ EC Mirror:
Connect the connector.
w/ Rain Sensor:
Connect the connector.
Connect the rear sliding roof drain hose.
Tech Tips
Use the same procedure for the LH side and RH side.
CONNECT MAP LIGHT ASSEMBLY
Engage the 4 clips and connect the map light assembly.
INSTALL SEAT BELT ANCHOR COVER
Engage the 5 guides, 4 claws and 3 clips, and install the seat belt anchor cover as shown in the illustration.
INSTALL VISOR HOLDER
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL VISOR ASSEMBLY RH
Install the visor assembly RH with 2 new visor arm set clips.
Engage the 2 clips to install the visor assembly RH.
INSTALL VISOR BRACKET COVER RH
Engage the 4 claws to install a new visor bracket cover RH.
INSTALL VISOR ASSEMBLY LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL VISOR BRACKET COVER LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL REAR ASSIST GRIP ASSEMBLY (w/ Coat Hook)
Tech Tips
Use the same procedure for the other rear assist grip.
Assemble the rear assist grip assembly as shown in the illustration.
Install the rear assist grip assembly.
INSTALL REAR ASSIST GRIP ASSEMBLY (w/o Coat Hook)
Tech Tips
Use the same procedure for the other rear assist grip.
Assemble the rear assist grip assembly as shown in the illustration.
Install the rear assist grip assembly.
INSTALL ASSIST GRIP SUB-ASSEMBLY
Tech Tips
Use the same procedure for the other rear assist grip.
Assemble the assist grip sub-assembly as shown in the illustration.
Install the assist grip sub-assembly.
INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
Engage the 2 claws.
Install the rain sensor cover as shown in the illustration.
INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
Engage the 2 claws.
Slide the inner rear view mirror stay holder cover and engage the 2 claws to install the cover as shown in the illustration.
INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY
Connect the connector.
Engage the 5 claws to install the integration control and panel assembly.
INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Monitor)
w/o Navigation System for HDD: Click here
w/ Navigation System for HDD: Click here
INSTALL TELEVISION BASE (w/ Rear Monitor)
w/o Navigation System for HDD: Click here
w/ Navigation System for HDD: Click here
INSTALL NO. 1 COOLER AIR DUCT
Install the No. 1 cooler air duct as shown in the illustration.
Engage the 2 claws to install the cooler plate.
INSTALL REAR NO. 2 SEAT TRACK ASSEMBLY RH
Install the rear No. 2 seat track assembly RH with the 2 bolts and 2 nuts.
INSTALL REAR ROOF SIDE RAIL GARNISH RH
*1 | Protective Tape |
Engage the 6 claws and 4 clips to install the rear roof side rail garnish RH.
Remove the applied protective tape on the rear roof side rail garnish RH.
INSTALL FRONT ROOF SIDE RAIL GARNISH RH
Engage the 5 clips and 9 claws to install the front roof side rail garnish RH.
INSTALL QUARTER LOCK PILLAR GARNISH RH
for 60/40 Split Seat Type:
Engage the 2 guides and 3 clips to install the quarter lock pillar garnish RH.
except 60/40 Split Seat Type:
Put the floor anchor part of the rear No. 1 seat belt assembly RH outer through the quarter lock pillar garnish RH as shown in the illustration.
Insert the 3 guides and engage the 3 claws, install the belt guide of the rear No. 1 seat belt assembly RH outer to the quarter lock pillar garnish RH.
Engage the 2 guides and 3 clips to install the quarter lock pillar garnish RH.
INSTALL UPPER ROOF SIDE INNER GARNISH RH
Engage the guide, claw and 2 clips to install the upper roof side inner garnish RH.
CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH
Install the shoulder anchor of the rear No. 2 seat outer belt assembly with the bolt.
Engage the 2 claws to close the cover.
INSTALL REAR SEAT HOOK SUB-ASSEMBLY RH
Engage the 2 guides as shown in the illustration.
Engage the 4 claws.
Install the rear seat hook sub-assembly RH with the 2 bolts.
INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH
Connect the connectors.
Engage the 2 guides, 7 claws and 14 clips to install the rear quarter trim panel assembly RH.
Install the clip(A).
INSTALL DECK SIDE GARNISH RH
Engage the 4 guides and 11 claws to install the deck side garnish RH as shown in the illustration.
CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (for 60/40 Split Seat Type)
Connect the floor end of the rear No. 1 seat outer belt assembly with the bolt.
INSTALL INNER LUGGAGE COMPARTMENT TRIM COVER RH (for 60/40 Split Seat Type)
Engage the 4 claws and install the inner luggage compartment trim cover RH.
INSTALL ROPE HOOK ASSEMBLY (for RH Side)
Install the rope hook assembly with the bolt.
Engage the 2 claws.
INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Install the bolt.
Push in the No. 1 luggage compartment trim and turn it clockwise approximately 90° to install the No. 1 luggage compartment trim hook.
INSTALL REAR ROOF SIDE RAIL GARNISH LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL FRONT ROOF SIDE RAIL GARNISH LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL QUARTER LOCK PILLAR GARNISH LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL UPPER ROOF SIDE INNER GARNISH LH
Engage the guide, claw and 2 clips to install the upper roof side inner garnish LH.
CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL REAR SEAT HOOK SUB-ASSEMBLY LH
Tech Tips
Use the same procedure for the LH side and RH side.
CONNECT POWER BACK DOOR ROD (w/ Power Back Door)
Install the power back door rod with the 2 bolts.
INSTALL REAR WINDOW SIDE GARNISH LH (w/ Power Back Door)
Engage the 3 clips and 2 claws to install the rear window side garnish LH.
INSTALL BACK DOOR NO. 2 SERVICE HOLE COVER (w/ Power Back Door)
Engage the 3 claws to install the back door No. 2 service hole cover.
INSTALL BACK DOOR CENTER GARNISH (w/ Power Back Door)
Engage the 6 clips and 4 claws to install the back door center garnish.
INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH
Engage the 2 guides, 8 claws and 15 clips, and install the rear quarter trim panel assembly LH.
Install the clip(A).
INSTALL DECK SIDE GARNISH LH
Engage the 4 guides and 12 claws to install the deck side garnish LH as shown in the illustration.
CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (for 60/40 Split Seat Type)
Tech Tips
Use the same procedure for the LH side and RH side.
REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER LH (for 60/40 Split Seat Type)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL ROPE HOOK ASSEMBLY (for LH Side)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM HOOK
Tech Tips
Use the same procedure for the No. 2 luggage compartment trim hook side and No. 1 luggage compartment trim hook side.
INSTALL REAR NO. 2 SEAT ASSEMBLY RH
Temporary install the rear No. 2 seat assembly.
Note
Do not damage the rear No. 2 seat assembly, body or body interior.
Connect the rear No. 2 seat outer belt assembly.
Temporary tighten the 2 nuts.
Lock the inner leg in the inner rail.
Remove the clip of the seat track upper rail cover.
Temporary install the seat track upper rail cover.
Adjust the rear No. 2 seat assembly so that the positioning marks are aligned as shown in the illustration.
As shown in the illustration, tighten the nut while pushing the rear No. 2 seat assembly towards the outside of the vehicle.
Note
If this operation is difficult to perform alone, use two or more people.
Make sure not to misalign the positioning marks when pushing the seat.
If the nut is tightened without the seat pushed towards the outside of the vehicle, the inner lock may not operate normally.
Remove the seat track upper rail cover.
As shown in the illustration, tighten the nut while pushing the rear No. 2 seat assembly towards the outside of the vehicle, and install the rear No. 2 seat assembly.
Note
If this operation is difficult to perform alone, use two or more people.
Make sure not to misalign the positioning marks when pushing the seat.
If the nut is tightened without the seat pushed towards the outside of the vehicle, the inner lock may not operate normally.
After reassembling the seat, check that the inner lock operates normally and that the inner lock and lock cover do not interfere with each other.
Check that the rear No. 2 seat flips up and slides smoothly. If abnormal, loosen the 2 nuts and perform operations starting from step (f) again.
Remove the 2 stopper bolts in the order indicated in the illustration.
Note
Before removing the stopper bolts, make sure that the inner leg is securely locked in the inner rail.
INSTALL NO. 1 SEAT TRACK LOCK PLATE COVER (for RH Side)
Engage the 2 claws and guide to install the No. 1 seat track lock plate cover.
INSTALL UPPER SEAT TRACK RAIL COVER RH
Engage the 2 claws to install the grommet.
Install the clip of the seat track upper rail cover.
Engage the 2 guides.
Engage the 5 claws and clip to install the upper seat track rail cover.
INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
Engage the claw to install the reclining adjuster release handle.
INSTALL REAR NO. 2 SEAT ASSEMBLY LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL NO. 1 SEAT TRACK LOCK PLATE COVER (for LH Side)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL UPPER SEAT TRACK RAIL COVER LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
Tech Tips
Use the same procedure for the RH side and the LH side.
INSTALL BACK DOOR SCUFF PLATE
Engage the 2 guides, 4 clips and 4 claws to install the back door scuff plate.
INSTALL BACK DOOR STRIKER COVER
Engage the 2 guides and 4 claws to install the back door striker cover.
INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
Tech Tips
It is possible to install the instrument panel register assembly with the upper instrument panel sub-assembly still installed to the vehicle body. Refer to the reassembly procedure for the upper instrument panel sub-assembly.
Engage the 5 claws.
Note
Do not allow the wire harness to get caught in the claws.
Make sure that the claws are fully engaged.
Engage the 9 claws.
Install the 2 clips.
Connect the connector.
Install the 2 passenger airbag bolts <A>.
Install the upper instrument panel sub-assembly with the 3 screws <B>.
CONNECT INSTRUMENT PANEL WIRE ASSEMBLY
Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Connect the connector.
Note
When connecting the airbag connector, take care not to damage the airbag wire harness.
Engage the wire harness clamp.
INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
Engage the 6 claws to install the No. 1 instrument panel box door sub-assembly.
Connect the connector.
INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Engage the 16 claws to install the No. 3 instrument cluster finish panel garnish.
Note
Make sure that the claws are fully engaged.
INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD)
Engage the 8 claws to install the No. 2 instrument cluster finish panel garnish.
Note
Make sure that the claws are fully engaged.
INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)
Engage the 8 claws to install the No. 2 instrument cluster finish panel garnish.
Note
Make sure that the claws are fully engaged.
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Connect the connector.
Engage the 23 claws to install the center instrument cluster finish panel sub-assembly.
Note
When installing the center instrument cluster finish panel sub-assembly, make sure to press the upper middle part firmly.
Make sure that the claws are fully engaged.
Remove the applied protective tape.
Move the shift lever to P.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Turn the shift lever knob clockwise to install the shift lever knob sub-assembly.
INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Engage the 15 claws.
Tech Tips
Before engaging the 15 claws, make sure that the claws are positioned correctly.
Note
Make sure that the claws are fully engaged.
Install the instrument cluster finish panel assembly with the bolt <C>.
INSTALL INSTRUMENT PANEL BOX ASSEMBLY
With the instrument panel box assembly opened approximately 60° from its closed position, engage the 2 hinges horizontally.
Note
Engaging the hinges from the top will deform the hinges. Be sure to install the instrument panel box assembly horizontally.
Install the damper clip.
Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the instrument panel box assembly.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.
Note
Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.
Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.
Engage the claw and connect the glove compartment door stopper.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect the connector.
Engage the 2 guides.
Engage the 4 claws to install the No. 2 instrument panel under cover sub-assembly.
Note
Make sure that the claws are fully engaged.
INSTALL CENTER FLOOR CARPET COVER LH
Engage the 4 claws.
Install the center floor carpet cover LH with the clip.
INSTALL CENTER FLOOR CARPET COVER RH (for RHD)
Engage the 4 claws.
Install the center floor carpet cover RH with the 2 clips.
INSTALL CENTER FLOOR CARPET COVER RH (for LHD)
Engage the 5 claws.
Install the center floor carpet cover RH with the clip.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)
Engage the 3 guides and 14 claws.
Tech Tips
Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.
Note
Make sure that the claws are fully engaged.
Install the lower instrument panel finish panel with the 3 screws <B>.
Engage the 3 claws and the fuel lid lock control cable assembly.
Engage the 3 claws and the hood lock control cable assembly.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)
Engage the 3 guides, 13 claws and clip.
Tech Tips
Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.
Note
Make sure that the claws are fully engaged.
Install the lower instrument panel finish panel with the 3 screws <B>.
Connect the fuel filler opening lid lock sub-assembly to the fuel lid lock open lever sub-assembly.
Engage the 3 claws and the fuel lid lock control cable assembly.
Engage the 3 claws and the hood lock control cable assembly.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
Engage the 2 claws and DLC3.
Engage the clamp.
Connect the connector.
Engage the 2 claws and 2 guides.
Note
Make sure that the claws are fully engaged.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
Engage the clamp.
Connect each connector.
Engage the 2 claws and guide.
Note
Make sure that the claws are fully engaged.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.
INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Connect the connector.
Engage the 4 claws to install the No. 1 instrument cluster finish panel garnish.
INSTALL COMBINATION METER ASSEMBLY
Connect the connector and temporarily install the combination meter assembly.
Note
When installing the combination meter assembly, do not damage the upper instrument panel sub-assembly and combination meter assembly.
Engage the 4 claws to install the combination meter assembly.
INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Engage the 11 claws and 2 guides to install the No. 1 instrument cluster finish panel.
Remove the protective tape from the steering column cover.
INSTALL UPPER CENTER PILLAR GARNISH RH
Engage the 2 guides.
Engage the 2 clips to install the upper center pillar garnish RH.
INSTALL LOWER CENTER PILLAR GARNISH RH
Engage the 4 claws and 3 clips to install the lower center pillar garnish RH as shown in the illustration.
INSTALL NO. 2 ASSIST GRIP (for RH Side)
Install the No. 2 assist grip with the 2 bolts.
INSTALL ASSIST GRIP PLUG (for Rear RH)
Engage the 4 claws to install the 2 assist grip plugs.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
Install the floor end of the front seat outer belt assembly with the bolt.
Check if the ELR locks.
Note
The check should be performed with the outer belt assembly installed.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
Engage the 3 claws to install the lap belt outer anchor cover.
CONNECT NO. 1 SLIDE DOOR WEATHERSTRIP RH
*1 | Alignment Mark |
*a | Pink |
*b | White |
Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the No. 1 slide door weatherstrip RH.
Note
After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE RH
Captain type rear seat:
Engage the 2 guides, 9 clips and 9 claws to install the rear door scuff plate RH.
Tip-up type rear seat:
Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.
Engage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration.
Using the slide lever, slide the rear No. 1 seat to the rearmost position.
Engage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration to install the rear door scuff plate RH.
*1 | Protective Tape |
Remove the protective tape applied to the bottom of the rear seat.
INSTALL FRONT LOWER PILLAR GARNISH RH
Engage the 4 claws to install the front lower pillar garnish RH.
INSTALL FRONT PILLAR GARNISH RH
*1 | Protective Tape |
*2 | Protective Cover |
*3 | Curtain Shield Airbag Assembly |
Remove the protective cover.
Engage the 6 guides and 2 clips to install the front pillar garnish RH.
INSTALL NO. 1 ASSIST GRIP (for RH Side)
Install the No. 1 assist grip with the 2 bolts.
INSTALL ASSIST GRIP PLUG (for Front RH)
Engage the 4 claws to install the 2 assist grip plugs.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
*1 | Alignment Mark |
*a | White |
Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the front door opening trim weatherstrip RH.
Note
After installation, check that the corners fit correctly.
INSTALL DOOR SCUFF PLATE ASSEMBLY RH
Engage the 3 guides, claw and 6 clips to install the door scuff plate assembly RH.
INSTALL COWL SIDE TRIM BOARD RH (for RHD)
Engage the 2 guides, claw and clip to install the cowl side trim board RH.
Install the clip(A).
INSTALL COWL SIDE TRIM BOARD RH (for LHD)
Engage the 2 guides, claw and the 2 clips to install the cowl side trim board RH.
Install the clip(A).
INSTALL UPPER CENTER PILLAR GARNISH LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL LOWER CENTER PILLAR GARNISH LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL NO. 2 ASSIST GRIP (for LH Side)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL ASSIST GRIP PLUG (for Rear LH)
Tech Tips
Use the same procedure for the LH side and RH side.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
Tech Tips
Use the same procedure for the LH side and RH side.
CONNECT NO. 1 SLIDE DOOR WEATHERSTRIP LH
*1 | Alignment Mark |
*a | White |
*b | Light Blue |
Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the No. 1 slide door weatherstrip LH.
Note
After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL FRONT LOWER PILLAR GARNISH LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL FRONT PILLAR GARNISH LH
*1 | Protective Tape |
*2 | Protective Cover |
*3 | Curtain Shield Airbag Assembly |
Remove the protective cover.
Engage the 6 guides and 2 clips, then install the front pillar garnish LH.
INSTALL NO. 1 ASSIST GRIP (for LH Side)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL ASSIST GRIP PLUG (for Front LH)
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
*1 | Alignment Mark |
*a | Yellow Green |
Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the front door opening trim weatherstrip LH.
Note
After installation, check that the corners fit correctly.
INSTALL DOOR SCUFF PLATE ASSEMBLY LH
Tech Tips
Use the same procedure for the LH side and RH side.
INSTALL COWL SIDE TRIM BOARD LH (for RHD)
Engage the 2 guides, claw and clip to install the cowl side trim board LH.
Install the clip(A).
INSTALL COWL SIDE TRIM BOARD LH (for LHD)
Engage the 2 guides, claw and clip to install the cowl side trim board LH.
Install the clip(A).
ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
INSTALL UPPER STEERING COLUMN COVER
Note
Installing the upper steering column cover in the incorrect order may break the claw and cause clearance between the upper steering column cover and lower steering column cover.
Engage the 4 clips and the 2 claws to install the upper steering column cover to the lower instrument cover.
Engage the claw and 2 pins to install the upper steering column cover to the steering column assembly.
INSTALL LOWER STEERING COLUMN COVER
Note
Installing the lower steering column cover in the incorrect order may break the claw and cause clearance between the upper steering column cover and lower steering column cover.
Engage the 2 claws to install the lower steering column cover to the upper steering column cover.
Engage the 2 claws.
Engage the claw.
Note
Press the area around the claw to engage it.
ADJUST SPIRAL CABLE
Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Rotate the spiral cable counterclockwise slowly by hand until it stops.
Note
Do not turn the spiral cable using the airbag wire harness.
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
Note
Do not turn the spiral cable using the airbag wire harness.
Tech Tips
The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
INSTALL STEERING WHEEL ASSEMBLY
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
INSTALL STEERING PAD
Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Connect the airbag connector to the steering pad.
Note
When connecting the airbag connector, take care not to damage the airbag wire harness.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of each "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
INSTALL LOWER NO. 3 STEERING WHEEL COVER
Engage the claw to install the lower No. 3 steering wheel cover.
INSTALL LOWER NO. 2 STEERING WHEEL COVER
Engage the claw to install the lower No. 2 steering wheel cover.
INSPECT STEERING WHEEL CENTER POINT
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSPECT STEERING PAD
Visually check for defects with the steering pad installed on the vehicle.
The defects are as follows:
Cuts on the surface and in the grooves of the steering pad
Small cracks on the surface and in the grooves of the steering pad
Significant discoloration on the surface and in the grooves of the steering pad
OK |
---|
No defects are found. |
Tech Tips
If any of the defects is found, replace the steering pad with a new one.
Make sure that the horn sounds.
Tech Tips
If the horn does not sound, inspect the horn system Click here.
INSPECT SRS WARNING LIGHT