NAVIGATION RECEIVER (for HDD) REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A003B3G

      Remove the clip and engine room side cover.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. A00EB81E01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. A00E7QBE01
      Text in Illustration
      *1 Protective Tape
      *2 Clamp
      *3 Guide

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and 5 claws.

    3. Detach the clamp.

    4. Detach the guide near the front of the vehicle and remove the finish panel.

  5. REMOVE NO. 3 BOX PANEL (w/o Console Box Lid)


    1. A003B2YE02
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 clips and remove the box panel.

  6. REMOVE NO. 3 BOX PANEL (w/ Console Box Lid)


    1. Place protective tape as shown in the illustration.

      A006SZ5E02
      Text in Illustration
      *1 Protective Tape
    2. Using a moulding remover B, detach the 6 clips and remove the box panel.

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

      A00E7Y2E01
  8. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for LHD)


    1. A00E70T

      Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

  9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (for RHD)


    1. w/o TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws and remove the panel end.

    2. w/ TOYOTA Parking Assist-sensor System:


      1. Using a moulding remover B, detach the 4 clips and 5 claws.

      2. Remove the panel end and then disconnect the connector.

        A00E8WSE01
  10. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY WITH FINISH PANEL


    1. A00E6R6E01
      Text in Illustration
      *1 Protective Tape

      Place protective tape as shown in the illustration.

    2. Using a moulding remover B, detach the 2 clips and hook.

    3. A00E7A7

      Detach the 3 claws and 3 hooks.

    4. Detach the 6 clips.

    5. A00EA2S

      Remove the panel register. Then disconnect the connector and detach the clamp.

  11. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET


    1. A003EHQ

      Remove the 4 screws.

    2. A003C67

      Pull the display to detach the 4 clips on the backside of the display.

    3. Disconnect the connectors and remove the navigation receiver.

  12. REMOVE NO. 1 RADIO BRACKET


    1. A003DZL

      Remove the 3 screws and bracket.

  13. REMOVE NO. 2 RADIO BRACKET


    1. A003BW4

      Remove the 3 screws and bracket.