SUSPENSION CONTROL ECU REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  3. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)


    1. Remove the rear No. 2 seat assembly LH Click here.

  4. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)


    1. Remove the rear No. 2 seat assembly LH Click here.

  6. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  7. REMOVE REAR STEP COVER

    A0159DZ

    Tech Tips

    Use the same procedure to remove the step cover on the other side.


    1. Detach the 2 claws and remove the step cover.

  8. REMOVE REAR DOOR SCUFF PLATE LH

    A015BJQ

    1. Remove the screw.

    2. Detach the 3 claws and 4 clips, and remove the scuff plate.

  9. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    A015BES

    1. Detach the 6 clips and remove the support plate.

  10. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

    A015DVZ

    Tech Tips

    Use the same procedure to remove the tonneau cover holder cap on the other side.


    1. Detach the 2 claws and remove the tonneau cover holder cap.

  11. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    A0155W0E01

    Tech Tips

    Use the same procedure to remove the rear seat cover cap on the other side.


    1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

      Tech Tips

      Tape the screwdriver tip before use.

  12. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    A0157OV

    Tech Tips

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. A0158A5

      Detach the 3 claws and remove the cover.

    2. A015CT4

      Remove the bolt and rear No. 1 seat belt anchor.

    3. A0156NH

      w/ Rear No. 2 Seat, except Face to Face Seat Type:

      Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 18 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

      4. w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

        A0157GF
    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

        A0158HZ
    6. w/ Tonneau Cover:


      1. Remove the screw and clip.

      2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

        A015ARP
  13. REMOVE REAR SIDE NO. 2 AIR DUCT (w/ Heater)

    A0155N3

    1. Remove the 3 screws and duct.

  14. REMOVE SUSPENSION CONTROL ECU


    1. A015E5I

      Detach the wire harness clamp and disconnect the connector.

    2. Remove the 2 bolts and ECU.