DESCRIPTION
Tech Tips
"Manual cut off switch" refers to the airbag cutoff switch cylinder.
The airbag cutoff switch cylinder circuit consists of the center airbag sensor and airbag cutoff switch cylinder.
The instrument panel passenger airbag and lower No. 2 instrument panel airbag can be optionally deactivated via this circuit by turning the airbag cutoff switch cylinder to the "OFF" position.
If the instrument panel passenger airbag and lower No. 2 instrument panel airbag are deactivated, the airbag cutoff indicator comes on to inform the passengers.
DTC B1651/33 is stored when a malfunction is detected in the airbag cutoff switch cylinder circuit.
DTC Code | DTC Detection Condition | Trouble Area |
---|---|---|
B1651/33 | One of the following conditions is met:
|
|
WIRING DIAGRAM
INSPECTION PROCEDURE
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.
Tech Tips
The 11 (MSW+) and 12 (MSW-) terminals in this circuit have an activation prevention mechanism. This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), it is necessary to release this mechanism.
PROCEDURE
CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - AIRBAG CUTOFF SWITCH CYLINDER)
*1 | Airbag Cutoff Switch Cylinder Sub-assembly |
*2 | Center Airbag Sensor Assembly |
*3 | Connector C |
*4 | Connector B |
*a | Front view of wire harness connector (to Airbag Cutoff Switch Cylinder Sub-assembly) |
*b | Rear view of wire harness connector (to Center Airbag Sensor Assembly) |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the center airbag sensor and airbag cut off switch cylinder.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
Standard Voltage | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | ||||||
---|---|---|---|---|---|---|
|
Release the activation prevention mechanism built into connector B Click here.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Restore the released activation prevention mechanism of connector B to its original condition.
NG |
REPLACE INSTRUMENT PANEL WIRE |
OK |
INSPECT AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY
Remove the airbag cutoff switch cylinder Click here.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
NG |
REPLACE AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY Click here |
OK |
CHECK CENTER AIRBAG SENSOR ASSEMBLY
*1 | Airbag Cutoff Switch Cylinder Sub-assembly |
*2 | Center Airbag Sensor Assembly |
Connect the connectors to the center airbag sensor and airbag cutoff switch cylinder.
Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in memory Click here.
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs Click here.
OK |
---|
DTC B1651/33 is not output. |
Tech Tips
Codes other than DTC B1651/33 may be output at this time, but they are not related to this check.
NG |
REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here |
OK |
USE SIMULATION METHOD TO CHECK Click here