Note
Before working on the fuel system, disconnect the cable from the auxiliary battery negative (-) terminal.
CAUTION:
Do not smoke or be near an open flame when working on the fuel system.
Keep gasoline away from rubber or leather parts.
Do not allow fuel to spray when removing the pipe between the high pressure side fuel pump and the fuel injector. The fuel in the pipe is highly pressurized.
PRECAUTION
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.
DISCHARGE FUEL SYSTEM PRESSURE
CAUTION:
Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.
Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
Even after discharging the fuel pressure, place a piece of cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.
Remove the rear seat cushion assembly Click here.
Remove the rear floor service hole cover.
Disconnect the fuel pump connector.
Put the engine in inspection mode Click here.
Start the engine. After the engine has stopped on its own, turn the power switch off.
Tech Tips
Some DTCs may be stored. Clear the DTCs before proceeding to the next step.
Crank the engine again and check that the engine does not start.
Loosen the fuel tank cap and discharge the pressure in the fuel tank completely.
Disconnect the cable from the auxiliary battery negative (-) terminal.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
Connect the fuel pump connector.
Install the rear floor service hole cover.
Install the rear seat cushion assembly Click here.
FUEL SYSTEM
When disconnecting a fuel pressure line, a large amount of gasoline will spill out. Perform the following procedure:
Discharge the fuel system pressure.
Put a container under the connection.
Disconnect the fuel pump tube.
Drain the fuel remaining inside the fuel pump tube into the container.
Cover the disconnected pipe and connector with a plastic bag to prevent damage and contamination.
Observe these precautions when disconnecting the fuel tube connector (for quick type A).
*1 | Fuel Hose Connector Cover |
Detach the lock claw by lifting up the fuel hose connector cover as shown in the illustration.
Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.
Pinch the connector and disconnect the connector and pipe.
*1 | Retainer |
Pinch | |
Pull |
Tech Tips
If the connector and pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.
Note
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
*1 | Retainer |
*2 | Nylon Tube |
*3 | Pipe |
*4 | O-Ring |
*5 | Fuel Tube Connector |
Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.
To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.
Observe these precautions when connecting the fuel tube connector (quick type A).
Check that there is no damage or contamination in the connecting part of the pipe.
Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline to the tip of the pipe.
Push |
Note
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After connecting the connectors and pipes, check if they are securely connected by trying to pull them apart.
Pull |
Attach the lock claw to the connector by pushing down on the fuel hose connector cover.
Check that there is no fuel leakage.
Observe these precautions when disconnecting the fuel tube connector (for quick type B).
Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.
Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.
*1 | Retainer |
Push | |
Down | |
Pull |
Tech Tips
If the connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.
Pull | |
Push |
Note
Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.
If the pipe and connector are stuck together, pinch the tube between your fingers and turn it carefully to free it. Then disconnect the main tube.
*1 | Pipe |
*2 | Retainer |
*3 | Nylon Tube |
*4 | Connector |
*5 | O-Ring |
Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.
To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.
Observe these precautions when connecting the fuel tube connector (for quick type B).
Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.
*1 | Retainer |
Up | |
Push |
Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and then push up on the retainer.
Note
Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.
Pull |
Observe the following precautions when disconnecting the fuel tube connector (for quick type C).
Check for dirt or mud on the fuel tube connector and pipe before disconnection. Clean if necessary.
*1 | Retainer |
Push | |
Pull up | |
Pull |
Pull the retainer up while pinching it on both sides by hand as shown in the illustration, and disconnect the fuel tube connector from the pipe.
Note
Do not use any tools.
If the fuel tube connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.
Note
Do not use any tools.
Check for dirt or mud on the pipe seal after disconnecting the fuel tube. Clean it if necessary.
Cover the disconnected fuel tube connector and pipe with a plastic bag.
Note
Do not allow the fuel tube connector or pipe to be damaged or contaminated by foreign matter.
Observe the following precautions when connecting the fuel tube connector (for quick type C).
*1 | Retainer |
Connect | |
Push down |
Align the shaft of the fuel tube connector with the shaft of the pipe, push the fuel tube connector in, and push down the retainer.
After connecting the fuel tube connector, check that the fuel tube connector and pipe are securely connected by trying to pull them apart.
FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Do not disconnect the tube shown in the illustration when disassembling the fuel suction with pump and gauge tube assembly. Doing so will cause reassembly of the fuel suction with pump and gauge tube assembly to be impossible as the tube is welded to the plate.
INSPECT FOR FUEL LEAK
Check that there are no fuel leaks anywhere on the fuel system after performing maintenance Click here.