FUEL SYSTEM ON-VEHICLE INSPECTION

PROCEDURE


  1. CHECK FUEL PUMP WITH FILTER ASSEMBLY OPERATION AND INSPECT FOR FUEL LEAK


    1. Check fuel pump with filter assembly operation.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

        Note

        Do not start the engine.

      3. Turn the GTS on.

      4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


        Powertrain > Engine and ECT > Active Test
        Tester Display
        Control the Fuel Pump / Speed

      5. Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the semiconductor pwr integration ECU, fuel pump with filter assembly, ECM and wiring connectors.

    2. Inspect for fuel leaks.


      1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

    3. Turn the power switch off.

    4. Disconnect the GTS from the DLC3.

  2. CHECK FUEL PRESSURE


    1. Discharge fuel system pressure.

      Click here

    2. Measure the auxiliary battery voltage.

      Standard Voltage
      11 to 14 V

    3. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    4. Disconnect the fuel tube sub-assembly (for Direct Injection).


      1. B008GCX

        Disconnect the fuel tube sub-assembly from the fuel pipe.

        Click here

    5. Disconnect the fuel tube sub-assembly (for Port Injection).


      1. B008GGF

        Disconnect the fuel tube sub-assembly from the fuel pipe.

        Click here

    6. B008GGWC07
      *1 Fuel Tube Sub-assembly (Vehicle Side)
      *a SST (Hose Band)
      *b SST (T-joint)
      *c SST (Gauge)
      *d SST (Hose Joint)
      *e SST (Hose)
      *f SST (Fuel Tube Connector)
      *g Fuel Pipe (Vehicle Side)

      Install SST (EFI fuel pressure gauge) as shown in the illustration.

      SST
      09268-45101   ( 09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070 )

    7. Wipe up any spilled fuel.

    8. Connect the cable to the negative (-) auxiliary battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    9. Connect the GTS to the DLC3.

    10. Turn the power switch on (IG).

      Note

      Do not start the engine.

    11. Turn the GTS on.

    12. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


      Powertrain > Engine and ECT > Active Test
      Tester Display
      Control the Fuel Pump / Speed

    13. Measure the fuel pressure.

      Standard Fuel Pressure
      196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)

      • If the fuel pressure is greater than the standard, replace the fuel pressure regulator assembly.

      • If the fuel pressure is less than the standard, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator assembly.

    14. Disconnect the GTS from the DLC3.

    15. Put the engine in inspection mode (maintenance mode).

      Click here

    16. Start the engine.

    17. Measure the fuel pressure at idle.

      Standard Fuel Pressure
      196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)

      Tech Tips

      Refer to Standard Idle Speed.

      Click here

    18. Stop the engine.

    19. After checking the fuel pressure, disconnect the cable from the negative (-) auxiliary battery terminal and carefully remove SST to prevent fuel from spraying.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    20. Connect the fuel tube sub-assembly to the fuel pipe (for Port Injection).


      1. Connect the fuel tube sub-assembly to the fuel pipe.

        Click here

    21. Connect the fuel tube sub-assembly to the fuel pipe (for Direct Injection).


      1. Connect the fuel tube sub-assembly to the fuel pipe.

        Click here

    22. Inspect for fuel leaks.

      Click here

  3. CHECK FUEL PRESSURE (for High Pressure)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Put the engine in inspection mode (maintenance mode).

      Click here

    5. Start and warm up the engine.

    6. Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


      Powertrain > Engine and ECT > Data List
      Tester Display
      Fuel Press

    7. Check the high pressure side fuel pressure.

      Standard Fuel Pressure
      2500 to 6000 kPa (25.5 to 61.2 kgf/cm2, 363 to 870 psi)

      If the pressure is not as specified, check the fuel pump with filter assembly, fuel pump with seal sub-assembly, fuel pressure sensor and wirings.

    8. Stop the engine.