ECD SYSTEM(w/o EGR Cooler), Diagnostic DTC:P062F

DTC Code DTC Name
P062F Internal Control Module EEPROM Error

DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P062F Internal Control Module EEPROM Error

When any condition below is met (1 trip detection logic):


  • Injector compensation code is not registered.

  • Wrong injector compensation code is registered.

  • Injector pilot quantity learning value is not registered.

  • Crank Time Compensation Learning value is not registered.*

*: When this malfunction occurs, the MIL does not illuminate.


  • Injector compensation code

  • Injector pilot quantity learning value

  • Crank time compensation learning value

  • ECM

Comes on DTC stored

Note


  • When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

  • Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

  • When an injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing pilot quantity learning values must be input into the new ECM.

Tech Tips

When replacing the ECM with a new one, if the injector compensation code and pilot quantity learning value are not entered or the injector compensation code is not registered correctly, DTC P062F will be stored.


  1. When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


    1. Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM Click here.

    2. After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS Click here.

    3. Turn the ignition switch off and turn the GTS off.

    4. Wait for at least 30 seconds.

    5. Turn the ignition switch to ON and turn the GTS on.

    6. Clear DTC P062F stored in the ECM using the GTS.


      Powertrain > Engine and ECT > Clear DTCs

      Tech Tips


      • Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the injector compensation codes to balance the different fuel injections between each injector assembly.

      • When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.

        Replacement Part Utility Item
        ECM
        Injector Assembly

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P062F Ignition switch ON for 1 second or more

CAUTION / NOTICE / HINT

Note


  • After replacing the ECM, the new ECM needs registration (Click here ) and initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. LEARNING VALUES CONFIRMATION


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.

      Click here


      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Confirmation
      Result
      Result Proceed to
      The injector compensation codes are not input A
      The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors B
      The pilot quantity learning values are set to the default values C
      Except above D

      Tech Tips

      When the pilot quantity learning values are set to the default values, "7FFF" is displayed.


    B
    C
    D
    A
  2. PERFORM LEARNING VALUES SAVE

    Tech Tips

    When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.


    1. Install the old ECM.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.

    5. Perform the Learning Values Save.

      Click here


      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Save
      Result
      Result Proceed to
      Learning Values Save is complete A
      Learning Values Save is fail B

    B
    A
  3. PERFORM LEARNING VALUES WRITE


    1. Remove the old ECM.

    2. Install a new ECM.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.

    5. Perform the Learning Values Write.

      Click here


      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Write
      Result
      Result Proceed to
      Learning Values Save is complete A
      Learning Values Save is fail B

    B
    A
  4. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs


      Powertrain > Engine and ECT > Clear DTCs
    3. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    4. Turn the ignition switch to ON for 1 second.

    5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    6. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      No DTC is output A
      P062F is output B

    A
    B
  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT
  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs
    3. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    4. Turn the ignition switch to ON for 1 second.

    5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    6. Confirm that the DTC is not output again.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT
  7. PERFORM LEARNING VALUES SAVE


    1. Remove the new ECM.

    2. Install the old ECM.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Save.

    5. Perform the Learning Values Save.

      Click here


      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Save
      Result
      Proceed to
      NEXT

    NEXT
  8. PERFORM LEARNING VALUES WRITE


    1. Remove the old ECM.

    2. Install a new ECM.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Values Write.

      Click here


      Powertrain > Engine and ECT > Utility
      Tester Display
      Learning Values Write
      Result
      Result Proceed to
      Learning Values Save is complete A
      Learning Values Save is fail B

    A
    B
  9. REGISTER INJECTOR COMPENSATION CODE


    1. Register the injector compensation code.

      Click here


      Powertrain > Engine and ECT > Utility
      Tester Display
      Injector Compensation
      Result
      Proceed to
      NEXT

    NEXT
  10. PERFORM PILOT QUANTITY LEARNING


    1. Perform the pilot quantity learning.

      Click here


      Powertrain > Engine and ECT > Utility
      Tester Display
      Pilot Quantity Learning
      Result
      Proceed to
      NEXT

    NEXT