REAR SEAT INNER BELT ASSEMBLY(for Fixed Seat Type) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat inner belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure	Necessary Procedures	Effects / Inoperative when not Performed	Link
Disconnect cable from negative (-) battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system	Click here
	Memorize steering angle neutral point	LKA/LDA system	Click here
		Parking support brake system*
		Pre-collision system
		Adaptive high beam system
		Lighting system (EXT) Cornering lights
		Variable gear ratio steering system	Click here
		Parking assist monitor system	Click here
		Panoramic view monitor system	Click here
	Initialize rear door sunshade system	Rear door sunshade system	Click here
	Initialize power trunk lid system	Power trunk lid system	Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

PROCEDURE

PRECAUTION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
1. Disconnect the cable from the negative (-) battery terminal.
  
  Click here
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  
  Click here
  
  If an SRS part is accidentally deployed, it may cause a serious injury.
  Note
  
  When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
  
  Click here
REMOVE REAR SEAT CUSHION ASSEMBLY

Click here
REMOVE REAR SEAT CUSHION LOCK HOOK

Click here
REMOVE NO. 1 SEAT ARMREST CAP

Click here
REMOVE REAR SEATBACK ASSEMBLY

Click here
REMOVE REAR SEATBACK HOLDER

Click here

REMOVE REAR SEAT INNER BELT ASSEMBLY LH

Remove in this Direction (1)

Remove in this Direction (2)

Pull in the removal direction (1) to detach the claw.
Detach the guide and remove the protector of the rear seat inner belt assembly LH in the removal direction (2) shown in the illustration.

*a	Clamp
*b	Guide
	Bolt
	Connector

Remove the bolt.

Disconnect the connector and detach the clamp.
Detach the guide and remove the rear seat inner belt assembly LH.

REMOVE REAR SEAT INNER BELT ANCHOR BRACKET SUB-ASSEMBLY LH
1. Remove the bolt and rear seat inner belt anchor bracket sub-assembly LH.

REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

Remove in this Direction (1)

Remove in this Direction (2)

Pull in the removal direction (1) to detach the claw.
Detach the guide and remove the protector of the rear seat inner with center belt assembly RH in the removal direction (2) shown in the illustration.

*a	Clamp
*b	Guide
	Bolt
	Connector

Remove the bolt.

Disconnect the connector and detach the clamp.
Detach the guide and remove the rear seat inner with center belt assembly RH.

REMOVE REAR SEAT INNER BELT ANCHOR BRACKET SUB-ASSEMBLY RH
1. Remove the bolt and rear seat inner belt anchor bracket sub-assembly RH.

	Remove in this Direction (1)
	Remove in this Direction (2)

	Remove in this Direction (1)
	Remove in this Direction (2)