REAR DOOR LOCK INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B0069V6C01
      B006DHE Install in this Direction

      Attach the clamp to install the rear door inside locking cable assembly as shown in the illustration.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B006B90C01
      B006DHE Install in this Direction

      Attach the clamp to install the rear door lock remote control cable assembly as shown in the illustration.

  3. INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH


    1. B006C5E

      Attach the claw.

    2. B006FCCC01
      B006DHE Install in this Direction

      Attach the claw to install the rear door lock cover sub-assembly LH as shown in the illustration.

  4. INSTALL REAR DOOR LOCK ASSEMBLY LH

    Note


    • When reusing a removed rear door lock assembly LH, replace the door lock wiring harness seal with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

    • Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock assembly LH.


    1. Apply MP grease to the sliding parts of the rear door lock assembly LH.

    2. B006A2D

      When reusing the rear door lock assembly LH:


      1. Install a new door lock wiring harness seal to the rear door lock assembly LH.

    3. B006B07C01
      *1 Release Plate
      B006DHE Install in this Direction

      Connect the rear door lock assembly LH to the release plate of the rear door outside handle frame sub-assembly LH, and set it to the rear door panel.

      Tech Tips

      Make sure that the release plate of the rear door outside handle frame sub-assembly LH is securely connected to the rear door lock assembly LH.

    4. Install the rear door lock assembly LH with the 2 bolts as shown in the illustration.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      Do not damage the vehicle body with rear door lock assembly LH.

      Tech Tips

      Install the rear door lock assembly LH while supporting it with one hand.

    5. B006FMYC01
      B006AHR "TORX" screw
      B006EC9 Connector

      Using a T30 "TORX" socket wrench, install the rear door lock assembly LH with the 3 TORX screws.

      Torque:
      7.3 N*m  { 74 kgf*cm, 65 in.*lbf }

    6. Connect the connector.

  5. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY LH

    Click here

  6. INSTALL REAR DOOR REAR WINDOW FRAME LH

    Click here

  7. INSTALL REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH

    Click here

  8. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  9. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH

    Click here

  10. INSTALL REAR DOOR GLASS RUN LH

    Click here

  11. INSTALL REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY LH

    Click here

  12. ADJUST REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

  13. INSTALL REAR DOOR OUTSIDE MOULDING INSERT LH

    Click here

  14. INSTALL REAR DOOR WINDOW FRAME MOULDING LH (REAR PILLAR SIDE)

    Click here

  15. INSTALL REAR DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

    Click here

  16. INSTALL REAR DOOR NO. 3 GLASS RUN LH

    Click here

  17. INSTALL REAR DOOR BELT MOULDING SUB-ASSEMBLY LH

    Click here

  18. INSTALL REAR DOOR BELT MOULDING LH

    Click here

  19. INSTALL REAR DOOR NO. 2 WEATHERSTRIP LH

    Click here

  20. INSTALL REAR DOOR FRONT BELT MOULDING END COVER LH

    Click here

  21. INSTALL REAR DOOR REAR BELT MOULDING END COVER LH

    Click here

  22. INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click here

  23. INSTALL REAR MULTIPLEX NETWORK DOOR ECU LH

    Click here

  24. INSTALL REAR SPEAKER ASSEMBLY

    Click here

  25. INSTALL REAR DOOR REAR BELT SEAL LH

    Click here

  26. INSTALL REAR DOOR FRONT BELT SEAL LH

    Click here

  27. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP LH

    Click here

  28. INSTALL REAR SIDE WINDOW COVER LH (w/ Rear Door Sunshade)

    Click here

  29. INSTALL REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)

    Click here

  30. INSTALL CURTAIN RAIL SIDE COVER LH (w/ Rear Door Sunshade)

    Click here

  31. INSTALL REAR DOOR FRAME GARNISH LH

    Click here

  32. INSTALL REAR DOOR NO. 2 FRAME GARNISH LH

    Click here

  33. INSTALL REAR DOOR TRIM COVER LH

    Click here

  34. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  35. INSTALL REAR DOOR NO. 2 ARMREST COVERLH

    Click here

  36. INSTALL REAR DOOR ARMREST COVER LH

    Click here

  37. INSTALL REAR DOOR TRIM UPPER COVER LH

    Click here

  38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    for 8GR-FKS:

    Click here

    for V35A-FTS:

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  39. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  40. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  41. CHECK POWER WINDOW CONTROL SYSTEM

    Click here

  42. INITIALIZE REAR DOOR SUNSHADE ASSEMBLY (w/ Rear Door Sunshade)

    Click here

  43. CHECK REAR DOOR SUNSHADE SYSTEM (w/ Rear Door Sunshade)

    Click here

  44. CHECK POWER DOOR LOCK CONTROL SYSTEM

    Click here