FRONT SEAT OUTER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic view monitor system

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

*: When performing learning using the GTS.
Click here Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    B006BC1

    Click here

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT BELT HOLE COVER LH

    Click here

  3. REMOVE SEAT BELT ANCHOR COVER CAP LH

    Click here

  4. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (SEAT ANCHOR)


    1. B006FQBC01
      B006DHE Remove in this Direction

      Remove the bolt.

    2. Detach the hook and remove the seat anchor of the front seat outer belt assembly LH from the hole of the front seat cushion shield LH.

  5. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  7. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  8. REMOVE CENTER LOWER PILLAR GARNISH LH

    Click here

  9. REMOVE CENTER UPPER PILLAR GARNISH LH

    Click here

  10. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    Tech Tips

    Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly LH.


    1. B006DQO

      Remove the screw and rib.

    2. B0069H9

      Detach the guide and remove the front shoulder belt anchor plate sub-assembly LH.

  11. REMOVE FRONT SEAT SHOULDER BELT GUIDE


    1. B006CZ6

      Remove the 2 screws.

    2. Detach the guide and remove the front seat shoulder belt guide.

  12. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B006BO4

      Remove the nut and shoulder anchor of the front seat outer belt assembly LH.

    2. B006DZZ

      Detach the 3 clamps and fold the floor carpet as shown in the illustration so that the clip of the No. 2 floor heater air duct LH can be removed.

    3. Remove the clip.

    4. B006DVX

      Move the No. 2 floor heater air duct LH as shown in the illustration so that the bolts of the retractor can be removed.

      Note

      Move the No. 2 floor heater air duct LH gently and do not damage it.

    5. B006FA0C01
      *a Locking Button
      B006GBM Protective Tape
      B006AHR Pretensioner Connector
      B006EC9 Tension Reducer Connector

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    6. Disconnect the tension reducer connector.

    7. B006BDZ

      Remove the 2 bolts.

    8. Detach the guide and remove the front seat outer belt assembly LH.

  13. REMOVE FRONT SEAT BELT RETRACTOR COVER LH


    1. B006FXWC01
      B006DHE Remove in this Direction (1)
      B006B42 Remove in this Direction (2)

      Pull in the removal direction (1) shown in the illustration to detach the claw.

    2. Slide in the removal direction (2) shown in the illustration to detach the guide and remove the front seat belt retractor cover LH.

  14. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. B006F7F

      Remove the 2 bolts.

    2. Detach the guide and remove the front shoulder belt anchor adjuster assembly.