OIL LEVEL SENSOR INSTALLATION

PROCEDURE


  1. INSTALL ENGINE OIL LEVEL SENSOR


    1. Install the engine oil level sensor with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Engage the 2 clamps.

    3. Install a new clip to the engine oil level sensor.

    4. Connect the engine oil level sensor connector.

  2. INSTALL OIL PAN SUB-ASSEMBLY


    1. w/o Canister Pump Module:


      1. B007YL2C01
        *a Seal Packing

        Apply seal packing in a continuous line as shown in the illustration.

        Seal Packing
        Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
        Standard Seal Packing Diameter
        2.5 to 3.5 mm (0.0984 to 0.138 in.)

        Note


        • Remove any oil from the contact surface.

        • Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.

        • Do not start the engine for at least 2 hours after installation.

        • Do not add engine oil for at least 2 hours after installation.

      2. B007ZEOC02
        *a Nut

        Temporarily install the oil pan sub-assembly with the 11 bolts and 2 nuts.

      3. B007X4OC02
        *a Nut

        Tighten the 2 bolts and nut in several steps in the order shown in the illustration.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      4. B007ZFLC02
        *a Torque Wrench Fulcrum Length

        Using SST, tighten the bolt (A).

        Torque:
        Specified tightening torque
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

        Tech Tips


        • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

          Click here

        • When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 5.2 N*m (53 kgf*cm, 46 in.*lbf)

      5. B007WWDC02
        *a Nut

        Tighten the 9 bolts and 2 nuts in several steps in the order shown in the illustration.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. w/ Canister Pump Module:


      1. B007Y6RC01
        *a Seal Packing

        Apply seal packing in a continuous line as shown in the illustration.

        Seal Packing
        Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
        Standard Seal Packing Diameter
        2.5 to 3.5 mm (0.0984 to 0.138 in.)

        Note


        • Remove any oil from the contact surface.

        • Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.

        • Do not start the engine for at least 2 hours after installation.

        • Do not add engine oil for at least 2 hours after installation.

      2. B007XMAC01
        *a Nut

        Temporarily install the oil pan sub-assembly with the 11 bolts and 2 nuts.

      3. B007Z84C01
        *a Nut

        Tighten the 2 bolts and nut in several steps in the order shown in the illustration.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      4. B007Y70C01
        *a Torque Wrench Fulcrum Length

        Using SST, tighten the bolt (A).

        Torque:
        Specified tightening torque
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

        Tech Tips


        • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

          Click here

        • When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 5.2 N*m (53 kgf*cm, 46 in.*lbf)

      5. B007XV2C01
        *a Nut

        Tighten the 9 bolts and 2 nuts in several steps in the order shown in the illustration.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  3. ADD ENGINE OIL

    Click here

  4. INSPECT FOR ENGINE OIL LEAK

    Click here

  5. CHECK ENGINE OIL LEVEL

    Click here