POP UP HOOD LIFTER(for Rear Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 2 pop up hood lifter assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic View Monitor System

Click here

Initialize Rear Door Sunshade System Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:

If the hood release lever is pulled after the No. 2 pop up hood lifter assembly is activated, the hood may rise more.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read precaution thoroughly before servicing.

    Click here

    B006BC1

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the pedestrian protection system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006BY6

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  5. REMOVE RADIATOR COVER PLATE

    Click here

  6. REMOVE FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP LH

    Click here

  7. REMOVE FRONT WIPER ARM HEAD CAP

    Click here

  8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

    Click here

  9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

    Click here

  10. REMOVE HOOD TO COWL TOP SEAL

    Click here

  11. REMOVE COWL TOP VENTILATOR LOUVER REINFORCEMENT

    Click here

  12. REMOVE CENTER NO. 2 COWL TOP VENTILATOR LOUVER

    Click here

  13. REMOVE CENTER COWL TOP VENTILATOR LOUVER

    Click here

  14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

    Click here

  15. REMOVE NO. 2 POP UP HOOD LIFTER ASSEMBLY LH

    CAUTION:


    • B006GNGC01
      B006GBM Extended Section

      When storing the No. 2 pop up hood lifter assembly LH, keep the No. 2 pop up hood lifter assembly LH extended section side facing upward.

    • If the No. 2 pop up hood lifter assembly LH deploys for any reason, it may cause a serious accident.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the pedestrian protection system.

      • If the pop up hood lifter assembly deploys for any reason, it may cause a serious accident.

      B006BY6
    3. B006C0SC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B006DHE Slide

      Disconnect pop up hood lifter connector.

      Note

      When disconnecting any pop up hood lifter connector, take care not to damage the wire harness.


      1. Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push the housing lock again and disconnect the connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the pop up hood lifter connector.

      3. After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B006F5DC07
        *a Correct *b Incorrect
        *c CPA *d Housing
    4. B006DQ6

      Detach the wire harness clamp.

    5. B006C59

      Remove the 2 nuts.

      CAUTION:

      Do not reuse the nut.

    6. B006FERC01
      B006DHE Remove No. 2 Pop Up Hood Lifter Assembly LH in this Direction
      B006B42 Remove Pop Up Hood Cover in this Direction

      Remove the No. 2 pop up hood lifter assembly LH.

    7. Detach the claw and remove the pop up hood cover.