PANORAMIC VIEW MONITOR SYSTEM PROBLEM SYMPTOMS TABLE

Note


  • The following inspection procedure of the panoramic view monitor system is described on the assumption that the audio and visual system*1 or navigation system*2 is normal. If the audio and visual system*1 or navigation system*2 has any malfunction, first proceed with troubleshooting of the audio and visual system*1 or navigation system*2.


    • *1: w/ Audio and Visual System (for 10.3 Inch Display)

    • *2: w/ Navigation System

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

    Click here

  • The following malfunctions may occur if a radio receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio receiver assembly, be sure to replace it with new one.


    • Communication malfunction DTC is output

    • Does not operate normally

Tech Tips

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

General
Symptom Suspected Area Link
Screen does not switch when the panoramic view monitor main switch is pressed. Refer to "Panoramic View Screen Description" in system description

Click here

Proceed to "ECU Power Source Circuit"

Click here

Diagnostic mode - Signal connection check (CAMERA SW check)

Click here

Parking assist ECU

Click here

Does not switch to the panoramic view and rear view screen when the shift lever is in R. Diagnostic mode - Signal connection check (CAN check)

Click here

Parking assist ECU

Click here

Image not displayed on the panoramic view and rear view screen or rear view screen when the shift lever is in R. Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Click here

Display does not switch to the see through view screen or moving view screen when the panoramic view monitor switch is pressed. Refer to "Panoramic View Screen Description" in system description

Click here

Diagnostic mode - Signal connection check (CAN check)

Click here

Diagnostic mode - Signal connection check (CAMERA SW check)

Click here

Parking assist ECU

Click here

Image not displayed on the see through view screen or moving view screen when the panoramic view monitor switch is pressed. Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Click here

Display does not switch to the panoramic view and wide front view screen, panoramic view and cornering view screen or the panoramic view and side clearance view screen when the panoramic view monitor main switch is pressed. Proceed to Description "Panoramic View Monitor Screen Display Conditions"

Click here

Diagnostic mode - Signal connection check (CAN check)

Click here

Diagnostic mode - Signal connection check (CAMERA SW check)

Click here

Parking assist ECU

Click here

Image not displayed on the panoramic view and wide front view screen, panoramic view and cornering view screen or the panoramic view and side clearance view screen when the panoramic view monitor main switch is pressed. Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Click here

Display does not switch to the retracted screen when the outer mirrors are retracted. Diagnostic mode - Signal connection check (CAN check)

Click here

Parking assist ECU

Click here

Display does not switch from the retracted screen when the outer mirrors are not in the retracted position. Diagnostic mode - Signal connection check (CAN check)

Click here

Parking assist ECU

Click here

Display Malfunction
Symptom Suspected Area Link
Objects not displayed correctly on the panoramic view monitor screen (color, distorted image). Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Click here

Distorted display on panoramic view screen. Camera view adjustment (calibration)

Click here

Parking assist ECU

Click here

Parking lines do not match at front and rear on panoramic view screen. Camera view adjustment (calibration)

Click here

Parking assist ECU

Click here

Partial black screen on panoramic view screen. Camera view adjustment (calibration)

Click here

Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Click here

Parking assist ECU

Click here

Area displayed differs from the actual area. Ensure no door is opened -
Camera view adjustment (calibration)

Click here

Parking assist ECU

Click here

Switch Function
Symptom Suspected Area Link
Combination switch assembly (panoramic view monitor main switch) night illumination does not illuminate. Inspect No. 2 combination switch assembly (panoramic view monitor main switch)

Click here

Harness and connector -
Remote touch switch operation is not accepted. Audio and visual system - Remote touch self check*1

Click here

Navigation system - Remote touch self check*2

Click here

Parking assist ECU

Click here

Radio receiver assembly

Click here

The remote touch function of the screen does not operate for the panoramic view monitor system. Parking assist ECU

Click here

Radio receiver assembly

Click here

Panoramic View Monitor System Function
Symptom Suspected Area Link
When the vehicle speed increases in the automatic display mode, the panoramic view and wide front view screen, panoramic view and cornering view screen, or the panoramic view and side clearance view screen remains displayed, without switching to the navigation screen. Replace parking assist ECU

Click here

The screen display timer function does not operate if the manual display mode is selected. Refer to "Panoramic View Screen Description" in system description

Click here

Parking assist ECU

Click here

The estimated course lines do not match the vehicle width extension lines when the steering wheel points straight ahead. Check the steering wheel installation angle

Click here

Adjust steering angle

Click here

Camera view adjustment (calibration)

Click here

Parking assist ECU

Click here

Estimated course lines stop moving before the steering wheel is turned fully left. Steering angle setting (calibrate stored maximum steering angle)

Click here

"!" is displayed and estimated course lines are not displayed. Check if the back door is not open -
Parking assist ECU

Click here

Audio and Visual System*1

Click here

Navigation System*2

Click here

Estimated course lines are not displayed. Check the panoramic view monitor screen display mode settings (Check if the estimated course lines display is set to off)

Click here

Parking assist ECU

Click here

"!" is displayed. Store the steering angle sensor steering neutral point

Click here

Diagnostic mode - Signal connection check (CAN check)

Click here

"!" remains displayed after the steering neutral point is stored. Adjust steering angle

Click here

Spiral with sensor cable sub-assembly Click here
Parking assist ECU

Click here

"!" is displayed and all the buttons on the screen are grayed out. Camera view adjustment (calibration)

Click here

Adjust steering angle

Click here

Audio and Visual System*1

Click here

Navigation System*2

Click here

"!" is displayed and all the buttons on the screen are grayed out even after parking assist ECU initialization has been completed. Parking assist ECU

Click here

Audio and Visual System*1

Click here

Navigation System*2

Click here

Guide lines and buttons are not displayed on the panoramic view and rear view screen display screen. Check if the back door is not open -
Check if the luggage compartment light assembly turns on and off normally (If not, refer to Lighting System (Interior) - Problem Symptoms Table)

Click here

Parking assist ECU

Click here

"CHK" is displayed for an item on the Vehicle Signal Check screen. Diagnostic mode - Signal connection check

Click here

Blind spots in image. Ensure no door is opened -
Camera view adjustment (calibration)

Click here

Camera boundary lines are poorly connected. Camera view adjustment (calibration)

Click here

Estimated course lines are displaced. Camera view adjustment (calibration)

Click here

Adjust steering angle

Click here

All buttons on the panoramic view monitor are continuously grayed out Audio and Visual System*1

Click here

Navigation System*2

Click here