Click here

HOOD LOCK CONTROL CABLE ASSEMBLY REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE RADIATOR SUPPORT OPENING COVER


    1. A01IS0M

      Remove the 3 clips.

    2. Detach the 4 hooks and remove the radiator support opening cover.

  4. Click here

    REMOVE FRONT FENDER LINER LH


    1. Remove the front fender liner (Click here).

  5. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Remove the 2 screws <A>.

    2. Detach the claw and guide, and remove the No. 1 instrument panel under cover.

  6. Click here

    REMOVE NO. 1 WATER HOSE CLAMP BRACKET


    1. Remove the 2 bolts, detach the 2 claws and remove the hose clamp bracket.

  7. Click here

    REMOVE HOOD LOCK ASSEMBLY


    1. for LHD:


      1. A01IS1Z

        Remove the 3 bolts and hood lock.

      2. A01IO2N

        Disconnect the hood lock control cable.

    2. for RHD:


      1. A01ITHB

        Remove the 3 bolts and hood lock.

      2. Disconnect the connector.

      3. A01IQR4

        Disconnect the hood lock control cable.

  8. Click here

    REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01IRIO

      Detach the 3 claws.

    2. Disconnect the hood lock control cable and remove the hood lock control lever.

  9. Click here

    REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. A01INSCE02

      Tie a string to the end of the hood lock control cable assembly as shown in the illustration.

      Note:

      Use a length of string long enough to pass through the engine compartment.

      Table 1. Text in Illustration
      *1 String
    2. A01IRBFE01

      Using a screwdriver, disconnect the clamps shown in the illustration.

      Table 2. Text in Illustration
      *1 Hood Lock Control Cable Assembly *2 Clamp
      *3 Radiator Support Side *4 Headlight
      *5 Wire Harness *6 Wire Harness Clamp
      *7 Dash Panel *8 Grommet
      *9 Hood Lock Control Cable Clamp - -
      Tip:

      Tape the screwdriver tip before use.

    3. Pull the cable out of the wheel housing from outside of the vehicle, and then untie the string and remove the cable.

  10. Click here

    REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. A01INSCE02

      Tie a string to the end of the hood lock control cable assembly as shown in the illustration.

      Table 3. Text in Illustration
      *1 String
      Note:

      Use a length of string long enough to pass through the engine compartment.

    2. A01ITR8E01

      Using a screwdriver, disconnect the clamps shown in the illustration.

      Table 4. Text in Illustration
      *1 Hood Lock Control Cable Assembly *2 Clamp
      *3 Radiator Support Side *4 Headlight
      *5 Wire Harness *6 Wire Harness Clamp
      *7 Dash Panel *8 Grommet
      *9 Hood Lock Control Cable Clamp *10 Radiator Hose
      *11 Washer Hose *12 Washer Hose Clamp
      Tip:

      Tape the screwdriver tip before use.

    3. Pull the cable out of the wheel housing from outside of the vehicle, and then untie the string and remove the cable.