POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    1. A01IQLV

      Using moulding remover A, detach the 3 claws and remove the inside handle bezel.

  4. REMOVE FRONT DOOR TRIM MOULDING LH


    1. A01IS9F

      Using moulding remover A, detach the 8 claws and remove the front door trim moulding.

  5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. A01IN0RE01

      Using moulding remover A, detach the clip and 7 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector.

  6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

    Tech Tips

    Use the same procedure described for the driver side.

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01IR1B

      Remove the 3 screws.

    2. Remove the 9 clips.

    3. w/ Courtesy Light:


      1. Disconnect the courtesy light connector.

    4. A01IP9CE01
      Text in Illustration
      *1 Reference Boss

      Pull out the rear door trim board in the direction indicated by the arrow.

    5. A01IUDS

      Disconnect the 2 cables from the inside handle.

  8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A01IUHM

      Detach the 2 claws and remove the inside handle sub-assembly from the door trim board.

  9. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    1. A01IUMH

      Detach the 5 claws and remove the weatherstrip.

  10. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01ISLX

      Using moulding remover D, detach the 3 claws and remove the outer mirror install hole cover.

  11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. for Driver Side:

      Temporarily install the master switch assembly.

    2. for Front Passenger Side:

      Temporarily install the regulator switch assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Move the door glass until the bolts appear in the service holes.

    5. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

    6. A01ITCI

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    7. A01IRRQ

      Remove the door glass in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

    8. for Driver Side:

      Remove the master switch assembly.

    9. for Front Passenger Side:

      Remove the regulator switch assembly.

  12. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH


    1. Disconnect the connector from the front door window regulator assembly.

    2. A01ITGNE01
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    3. Remove the 5 bolts.

    4. Remove the front door window regulator assembly.

    5. Remove the temporary bolt from the front door window regulator assembly.